Matronics Email Lists

Thanks very much Eric, that's really helpful and much appreciated.
Chris

Any recommendations for p/n that would be a suitable diode to use for isolating ECU's, or ignition coils?
Was there a wiring diagram available Bill, I would be very interested to see if if there is. ...

Hi Bill
It's been along time since I have posted on aeroelectric . The way I think I read your issue is that you don't want to backfeed from one bus to the other in fear of blowing the protective fus ...

Hi BobVery interested in a kit or a completed and tested one.
Â Thanks
Â Â Chris

On Fri., Feb. 9, 2024, 9:10 a.m. Robert L. Nuckolls, III, <nuckolls.bob@aeroelectric.com ( Boards are on o ...

Thanks everyone for your input. I will wire it up as suggested.
Chris

Hi All
I have finished wiring a very simple single place biplane with a VW engine. The engine has single ignition, automotive style with coil and breaker points. I used a master switch to turn o ...

Hi Bob and All.
Thanks for all the help Bob, the Zodiac 601 was test flow today and the Microair radio is working great, no more whine and no noise! Putting in a forest of tabs got rid of al ...

Hi Bob and All
I had a chance to do some work on the Zodiac 601 with a jabiru engine again. The problem is the Microair radio has a very loud hum when transmitting. The voice is clear but alon ...

â€œ Is the microphone jack electrically isolated
from the airframe? Further, does it's ground wire
route in parallel with mic audio and ptt lines
back to the radio?â€
Not sure ab ...

Hi All
A friend of mine has purchased a Zodiac 601 with a Jabiru engine. The problem was originally lots of noise in the headsets. We rewired the grounding , installed a forest of tabs on the f ...

Just hoping someone else has run across this problem and better still has a solution. I have a new Garmin 327 installed in a ragwing aircraft. When the Transponder is switched to Alt. the correct a ...

Hi Matt
Another trick to try before you start squeezing ailerons is to cut a V block of dense wood or plastic to the shape of the trailing edge of the ailerons from the plans.Place this block ...

Hi
I'm working on a friends RV6 and we have a problem with a Vans Manifold pressure gauge. When power is applied the needle swings full scale. I'm suspecting the sensor, it has 4 wires coming f ...

Hey fellas
I have a Rotax 912UL muffler for sale. It's stainless, in very good condition. I believe it came from an Evektor LSA. $250.00. Please contact Chris fconsult@telus.net (

...

Muffler for Rotax 912uls, used very little in excellent condition, was off a Evector. $200.00.+ shipping Thanks. email - fconsult@telus.net (
[quote][b]

Hey Vince
I'm at the same place, having put a NACA vent under the wing - works
great for the rear seater, I haven't put anything up front for myself yet, I
was trying to run a vent behind ...

An update on the trim problem I am having with the gearleg fairings. I re
rigged the port fairing, by digging out all the foam and refoaming top and
bottom. I moved the gearleg fairing ,trailing edg ...

Hey Fellas
I've been flying my Harmon Rocket for a grand total of 5 hours now
and all was going well until I put on the gearleg fairings and wheelpants.
When I first flew it without the ...

Hi
I'm looking for advice on a cowl -- fuel injector servo clearance
problem. I have a HRII with Airflow Performance Fuel injector servo and
elbow. There is lots of clearance between the elbow ...

Hi John
Rocket is getting really close, just finished wiring, things light up
and the smoke stays in! Have to finish engine baffling and cowling, then its
off to the hangar (CYBL - Campbell ...