Matronics Email Lists

Tim is right

the info can be found in the shop
I think but am not 100% sure, that you're looking for a 3/8" NPT plug.
Tim

On 4/13/ ...

So it would look something like this, only long wire would be #3 but could be disconnected via the relay high concentration on starter contactor now of # of connection

--&g ...

Hi Joe,

how could I doubt your advice Sad

(I just overlooked that path via the diode)

That is very elegant, as the Aux would source the whole system the wire
run would be short (and common to bo ...

Thanks a lot Joe for your thoughts,

if I connect the wire 1 at the starter contactor I would defy the idea
of Z101, that the aux alternator can feed the essential bus without
switching on the mai ...

Good morning,

there is not a lot of echo on my question, I would appreciate if the "usual suspects" Wink

could give me a short feedback if I'm on the right way to reduce w ...

Hi folks,

I have an additional question here concerning Z101 which I use in my RV-10

Thanks M,

that is it, sorry got that mail in the spam folder lost before seen now.

Cheers Werner

On 04.12.2023 16:29, M Wilson wrote:
[quote] It looks like you need a DP3T switch. Do a sea ...

Thanks Chuck,

I did that beforehand, however it needs some bridging of some contacts
to achieve what I need, Bob's link did provide that information.

Cheers Werner

On 05.12.2023 15:43, Chuck ...

Thanks Bob,

with the 5A rating that switch has enough "OOMPS" and will perfectly fit my needs Smile

))

appreciated!

Werner

On 04.12.2023 1 ...

Thanks M,

the circuit shown for the dimmer is not exactly the product used, the
Perhelion dimer has an integrated on-off switch. And the LED's are
strips with resistors for 12 V.

The problem I ...

Thanks Bob,

The dimmer has the off functionality, so 3 position would work but need
to have 2 feeders, diodes would be against crossfeed here my
architecture, but the switch will not work this wa ...

Christopher, that is the same as below, due to 2 feeds it does not work

Cheers Werner

On 02.12.2023 16:31, Christopher Cee Stone wrote:

...

Thanks Christopher,

but they do not work as they have not 3 independent position

Many from on-line vendors: --> AeroElectric-List message p ...

Hello Charlie,

good question to consider, it's in a center overhead console and I guess 90 of the time the switch would be in the center position (dimmer for both), the rear posit ...

Hi Folks,

I wonder if I could save on a 4th dimmer Wink

Here what I want to achieve:

Cabin lights (LED) 2 section, front and rear:

-position 1, front lights on dimmer, rear lights off
-positio ...

Billski,

which gear ratio did you use and for what plane type?

Cheers Werner

On 18.11.2023 17:01, wsimpso1 wrote:

Charlie,

Not Menzimer, using Actuonix P-16P for elevators, P-16L fo ...

Hi there,

I found this part and first thought it might be the F1011 bracket for the cables, but meanwhile I doubt, the nomination would tell it is in the fuselage kit included, bu ...

Charlie here Revision B,

aux Load on Essential down to 20A, 5 SPare slots on Main Bus, 2 on
Essential, a bit to redo and order another Busmann block for Bat bus.

Cheers Werner

On 06.06.2023 ...

Thanks Charlie,

I will reconsider and thinking about 2 10 blockes at the position of the
20 block. the aux should, from the calculation, be more then ok to keep
the current essential load but aga ...

Thanks Charlie,

I thought about adding but then, is there a drawback to have a tad more
(about 4) on the essential (as I have aux generator) so the battery only
operation is a very very low proba ...