Matronics Email Lists Forum Index Matronics Email Lists
Web Forum Interface to the Matronics Email Lists
 
 Get Email Distribution Too!Get Email Distribution Too!    FAQFAQ   SearchSearch   MemberlistMemberlist   UsergroupsUsergroups   RegisterRegister 
 ProfileProfile   Log in to check your private messagesLog in to check your private messages   Log inLog in 

Suggestion on the needed tool.

 
Post new topic   Reply to topic    Matronics Email Lists Forum Index -> RV10-List
View previous topic :: View next topic  
Author Message
indigoonlatigo(at)msn.com
Guest





PostPosted: Sun Jan 08, 2006 6:45 pm    Post subject: Suggestion on the needed tool. Reply with quote


Hello all,
I am trying to finish up dimpling all my elevator parts and have two problem
areas. The last three holes in the elevator tip rib flange at the trailing
edge are so close to the opposite flange there is no room to get in there.
Are these three holes best to countersink even know the rib skin is thin?
Lastly, the rear elevator spar is so narrow that again my pnuematic dimpler
present a problem as the only way to get the male die to get into its hole
is to carefully get the male dimple to start to move, then line it up and
then go for it. Maybe I could do this with one hole but not the 200 or so,
this is suicide. I do not own a hand squezer/rivetter. Any suggestions
short of purchasing the manual dimpler?
THANKS,
John G. #40409


- The Matronics RV10-List Email Forum -
 

Use the List Feature Navigator to browse the many List utilities available such as the Email Subscriptions page, Archive Search & Download, 7-Day Browse, Chat, FAQ, Photoshare, and much more:

http://www.matronics.com/Navigator?RV10-List
Back to top
LloydDR(at)wernerco.com
Guest





PostPosted: Sun Jan 08, 2006 7:14 pm    Post subject: Suggestion on the needed tool. Reply with quote


Avery has Vice grip dimplers for tight areas. There is also a pop rivet
dimple tool, that you can use without the nail, and squeeze them with a
pair of pliers


- The Matronics RV10-List Email Forum -
 

Use the List Feature Navigator to browse the many List utilities available such as the Email Subscriptions page, Archive Search & Download, 7-Day Browse, Chat, FAQ, Photoshare, and much more:

http://www.matronics.com/Navigator?RV10-List
Back to top
VHMUM(at)bigpond.com
Guest





PostPosted: Sun Jan 08, 2006 7:31 pm    Post subject: Suggestion on the needed tool. Reply with quote


For the ellevator use a pop rivet dimpler which you will use in several
other places and no hand squeezer???? Borrow one!
Chris


- The Matronics RV10-List Email Forum -
 

Use the List Feature Navigator to browse the many List utilities available such as the Email Subscriptions page, Archive Search & Download, 7-Day Browse, Chat, FAQ, Photoshare, and much more:

http://www.matronics.com/Navigator?RV10-List
Back to top
moons1999(at)yahoo.com
Guest





PostPosted: Sun Jan 08, 2006 7:51 pm    Post subject: Suggestion on the needed tool. Reply with quote


John,
  I just finished those dimples myself.  For the rear spar I did exactly what you indicated below and went VERY slow with it.  Didn't miss on any of the holes.  For the last holes in that rib I went to Home Depot and picked up a 1" C clamp.  I plan on using my close-quarters dies with the C clamp instead of the pop rivet gun.  I haven't done it yet, but I figure it will work out pretty well.  Another option is the vice-grip dimplers that Avery has or the tight fit dimpling tool from Cleaveland.  I just didn't want to wait for another tool to ship, which is why I didn't go with either of these solutions.
 
--Shawn
40366
John Gonzalez <indigoonlatigo(at)msn.com> wrote:
Got holiday prints? [url=http://us.rd.yahoo.com/mail us/taglines/holidayprints/*http://pa.yahoo.com/*http://us.rd.yahoo.com/mail us/taglines/photos/evt=38089/*http://pg.photos.yahoo.com/ph//print splash]See all the ways[/url] to get quality prints in your hands ASAP.


- The Matronics RV10-List Email Forum -
 

Use the List Feature Navigator to browse the many List utilities available such as the Email Subscriptions page, Archive Search & Download, 7-Day Browse, Chat, FAQ, Photoshare, and much more:

http://www.matronics.com/Navigator?RV10-List
Back to top
indigoonlatigo(at)msn.com
Guest





PostPosted: Mon Jan 09, 2006 8:47 am    Post subject: Suggestion on the needed tool. Reply with quote


Thanks for the direction, I placed the Avery order already. Too many holes
on the rear spar to wing it!
John
Quote:
From: "Lloyd, Daniel R." <LloydDR(at)wernerco.com>
Reply-To: rv10-list(at)matronics.com
To: <rv10-list(at)matronics.com>
Subject: RE: RV10-List: Suggestion on the needed tool.
Date: Sun, 8 Jan 2006 22:14:01 -0500
Avery has Vice grip dimplers for tight areas. There is also a pop rivet
dimple tool, that you can use without the nail, and squeeze them with a
pair of pliers

- The Matronics RV10-List Email Forum -
 

Use the List Feature Navigator to browse the many List utilities available such as the Email Subscriptions page, Archive Search & Download, 7-Day Browse, Chat, FAQ, Photoshare, and much more:

http://www.matronics.com/Navigator?RV10-List
Back to top
Display posts from previous:   
Post new topic   Reply to topic    Matronics Email Lists Forum Index -> RV10-List All times are GMT - 8 Hours
Page 1 of 1

 
Jump to:  
You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot vote in polls in this forum
You cannot attach files in this forum
You can download files in this forum


Powered by phpBB © 2001, 2005 phpBB Group