Matronics Email Lists Forum Index Matronics Email Lists
Web Forum Interface to the Matronics Email Lists
 
 Get Email Distribution Too!Get Email Distribution Too!    FAQFAQ   SearchSearch   MemberlistMemberlist   UsergroupsUsergroups   RegisterRegister 
 ProfileProfile   Log in to check your private messagesLog in to check your private messages   Log inLog in 

Vibrating control

 
Post new topic   Reply to topic    Matronics Email Lists Forum Index -> Yak-List
View previous topic :: View next topic  
Author Message
Jacquescj6



Joined: 20 Dec 2011
Posts: 23
Location: Swakopmund , Namibia

PostPosted: Tue May 06, 2014 1:31 pm    Post subject: Vibrating control Reply with quote

Hi All
I have just replaced an engine and prop in my cj6 and now have a bit of a vibration.

On low Rpm it feels normal but at about 1200rpm there is a bit of vibration
on the aircraft taxing at higher rpm about 1400 rpm it seem to go away.

while flying there is a definite vibration on the stick.
At low rpm 1700 to 1900 the vibration its not to bad and I would describe it as a slow vibration but as you increase the rpm the vibration speeds up quite a bit shaking the stick . It does not feel as if the air frame is shaking abnormally but only on the stick.

Does anybody have a suggestion as to what it could be or is it just an unbalance prop.


- The Matronics Yak-List Email Forum -
 

Use the List Feature Navigator to browse the many List utilities available such as the Email Subscriptions page, Archive Search & Download, 7-Day Browse, Chat, FAQ, Photoshare, and much more:

http://www.matronics.com/Navigator?Yak-List
Back to top
View user's profile Send private message Send e-mail
richard.goode(at)russiana
Guest





PostPosted: Tue May 06, 2014 11:49 pm    Post subject: Vibrating control Reply with quote

The obvious question is whether you have dynamically balanced the propeller
after changing it. We regard this as absolutely vital to smooth operation.

Richard Goode Aerobatics
Rhodds Farm
Lyonshall
Hereford
HR5 3LW

Tel: +44 (0) 1544 340120
Fax: +44 (0) 1544 340129
www.russianaeros.com

--


- The Matronics Yak-List Email Forum -
 

Use the List Feature Navigator to browse the many List utilities available such as the Email Subscriptions page, Archive Search & Download, 7-Day Browse, Chat, FAQ, Photoshare, and much more:

http://www.matronics.com/Navigator?Yak-List
Back to top
wlannon(at)shaw.ca
Guest





PostPosted: Wed May 07, 2014 7:29 am    Post subject: Vibrating control Reply with quote

A few questions on your prop installation;

Was this a new prop. in 2 steel boxes from China. If so it would be
perfectly balanced assuming you have set the blade angles correctly - with a
propellor protractor, and properly positioned and torqued the clamps.
While I agree with Richard about dynamic balancing that is a final step to
match a properly balanced propellor with the rotating mass of the engine.
Correct installation comes first.

Please advise the details of the prop and engine you installed.

Walt

--


- The Matronics Yak-List Email Forum -
 

Use the List Feature Navigator to browse the many List utilities available such as the Email Subscriptions page, Archive Search & Download, 7-Day Browse, Chat, FAQ, Photoshare, and much more:

http://www.matronics.com/Navigator?Yak-List
Back to top
Jacquescj6



Joined: 20 Dec 2011
Posts: 23
Location: Swakopmund , Namibia

PostPosted: Wed May 07, 2014 11:56 am    Post subject: Re: Vibrating control Reply with quote

Hi
Thanks for the reply's.
It was used blades I got from the guy I bought the plane from After installing the blades we did discovered that the no 1 blade was a bit longer than the no 2 blade?

I have taken them off and send them to our local propeller shop to do a static balance and then we will do a dynamic balance and see if it is better.

Will let you guys know.


- The Matronics Yak-List Email Forum -
 

Use the List Feature Navigator to browse the many List utilities available such as the Email Subscriptions page, Archive Search & Download, 7-Day Browse, Chat, FAQ, Photoshare, and much more:

http://www.matronics.com/Navigator?Yak-List
Back to top
View user's profile Send private message Send e-mail
wlannon(at)shaw.ca
Guest





PostPosted: Wed May 07, 2014 6:17 pm    Post subject: Vibrating control Reply with quote

You will need to send them the hub also. They will have to match the two
blades in length, width and thickness before installing in the hub for both
horizontal and vertical static balance.
Unbalance correction is made with steel plates attached to the hub assy.
After that it should be good assuming the blade angles are set within
tolerance which is 0.1 deg (6 min.). I try to set them within 0.05 deg. (3
min.)

Dynamic balance may not work very well on this prop. as there is no spinner
structure. For dynamic balance the corrective weight could be required
anywhere within 360 degs. With no spinner plate to accommodate that you are
restricted to a limited area at each blade only.

Walt

--


- The Matronics Yak-List Email Forum -
 

Use the List Feature Navigator to browse the many List utilities available such as the Email Subscriptions page, Archive Search & Download, 7-Day Browse, Chat, FAQ, Photoshare, and much more:

http://www.matronics.com/Navigator?Yak-List
Back to top
Jacquescj6



Joined: 20 Dec 2011
Posts: 23
Location: Swakopmund , Namibia

PostPosted: Fri May 09, 2014 12:26 pm    Post subject: Re: Vibrating control Reply with quote

Hi
Update on the prop.
According to the prop shop the one blade is quite a bit heavier than the other one.
If any one has got some type of diagram on how to add weight in the blades
I would appreciate it
Thanks


- The Matronics Yak-List Email Forum -
 

Use the List Feature Navigator to browse the many List utilities available such as the Email Subscriptions page, Archive Search & Download, 7-Day Browse, Chat, FAQ, Photoshare, and much more:

http://www.matronics.com/Navigator?Yak-List
Back to top
View user's profile Send private message Send e-mail
Jacquescj6



Joined: 20 Dec 2011
Posts: 23
Location: Swakopmund , Namibia

PostPosted: Sat May 24, 2014 12:06 pm    Post subject: Re: Vibrating control Reply with quote

Hi All
Just an update on the vibrations.
The propshop did a static balance and wala the vibration is now gone.
Thanks for all the help guys.


- The Matronics Yak-List Email Forum -
 

Use the List Feature Navigator to browse the many List utilities available such as the Email Subscriptions page, Archive Search & Download, 7-Day Browse, Chat, FAQ, Photoshare, and much more:

http://www.matronics.com/Navigator?Yak-List
Back to top
View user's profile Send private message Send e-mail
Display posts from previous:   
Post new topic   Reply to topic    Matronics Email Lists Forum Index -> Yak-List All times are GMT - 8 Hours
Page 1 of 1

 
Jump to:  
You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot vote in polls in this forum
You cannot attach files in this forum
You can download files in this forum


Powered by phpBB © 2001, 2005 phpBB Group