Matronics Email Lists Forum Index Matronics Email Lists
BBS Forum Interface to the Matronics Email Lists
 
 Get Email Distribution Too!Get Email Distribution Too!    FAQFAQ   SearchSearch   MemberlistMemberlist   UsergroupsUsergroups   RegisterRegister 
 ProfileProfile   Log in to check your private messagesLog in to check your private messages   Log inLog in 

MurphyMoose-List Digest: 1 Msgs - 07/22/16

 
Post new topic   Reply to topic    Matronics Email Lists Forum Index -> MurphyMoose-List
View previous topic :: View next topic  
Author Message
sapril001(at)hotmail.com
Guest





PostPosted: Sat Jul 23, 2016 4:17 am    Post subject: MurphyMoose-List Digest: 1 Msgs - 07/22/16 Reply with quote

Hi,


I forgot about the last wing tip bearing on the ailerons [img]data:image/png;base64,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[/img], you have to be careful when tightening the bolts on all the bushings/brass bearings in the ailerons system, 4 ailerons bushings and one torque tube bushing inside the wing. A total of 10 places not 8 as I said. The same also apply for the flaps bushings.


Regards
Sylvain April




From: owner-murphymoose-list-server(at)matronics.com <owner-murphymoose-list-server(at)matronics.com> on behalf of MurphyMoose-List Digest Server <murphymoose-list(at)matronics.com>
Sent: July 23, 2016 3:01:57 AM
To: MurphyMoose-List Digest List
Subject: MurphyMoose-List Digest: 1 Msgs - 07/22/16


*

=========================
Online Versions of Today's List Digest Archive
=========================

Today's complete MurphyMoose-List Digest can also be found in either of the
two Web Links listed below. The .html file includes the Digest formatted
in HTML for viewing with a web browser and features Hyperlinked Indexes
and Message Navigation. The .txt file includes the plain ASCII version
of the MurphyMoose-List Digest and can be viewed with a generic text editor
such as Notepad or with a web browser.

HTML Version:

http://www.matronics.com/digest/digestview.php?Style=82701&View=html&Chapter=2016-07-22&Archive=MurphyMoose

Text Version:

http://www.matronics.com/digest/digestview.php?Style=82701&View=txt&Chapter=2016-07-22&Archive=MurphyMoose


=======================
EMail Version of Today's List Digest Archive
=======================


----------------------------------------------------------
  MurphyMoose-List Digest Archive
  ---
  Total Messages Posted Fri 07/22/16: 1
----------------------------------------------------------


Today's Message Index:
----------------------

1. 06:07 AM - Re: MurphyMoose-List Digest: 1 Msgs - 07/21/16 (Sylvain)



________________________________ Message 1 _____________________________________


Time: 06:07:14 AM PST US
From: Sylvain <sapril001(at)hotmail.com>
Subject: Re: MurphyMoose-List Digest: 1 Msgs - 07/21/16

Hi,

Yes there are interference, the push rod that move the ailerons goes throug
h a hole in the aft spar of the wing, this hole is to small, it need to be
elongated at the bottom to allow full operation of the ailerons when the fl
aps are down. If the hole is not enlarged, when the flaps are down the aile
rons also come down and the rod enter in contact with the spar and limit th
e aileron downward movement.


Other than that you will have to make new hole to attach the ailerons pushr
ods, inside the airplane and outside on the horns, this to obtain more rota
tion on the aileron torque tube with the same input on the control stick. 
Some peoples have modified their control stick pivot to get more input moti
on on the aileron cable, I choose to drill new holes to attach the push rod
s, simpler and I get the final rotation I need. The ailerons are not heavy
on the moose as some peoples have said, I think that that heaviness that th
ey have felt must be from over torquing the ailerons mounting bolts, I have
done it and the result is that the stainless bushings inside the brass bea
ring is swelling and cause a friction, this can happen 4 places X 2 , 3 ail
erons bushing and the torque tube bushing inside each wing.


For the flaps 39 degrees, it is the same the cable attach point on the top
of the airplane where it pull on the horn need to be move at a lower point
so with the same input on your flap lever you will get the right 39 degrees
of deflection. It work well 13,26,39. degrees. This make your flaps feel
heavier but not much. Just make sure your lever mechanism is working freely
and the locking bolt enter the notches freely, I had to do some filing the
re so it work well.


Good luck


Sylvain April

C-GFFO


________________________________
From: owner-murphymoose-list-server(at)matronics.com <owner-murphymoose-list-s
erver(at)matronics.com> on behalf of MurphyMoose-List Digest Server <murphymoo
se-list(at)matronics.com>
Sent: July 22, 2016 3:01:42 AM
Subject: MurphyMoose-List Digest: 1 Msgs - 07/21/16

*

========================

Online Versions of Today's List Digest Archive
========================


Today's complete MurphyMoose-List Digest can also be found in either of the
two Web Links listed below. The .html file includes the Digest formatted
in HTML for viewing with a web browser and features Hyperlinked Indexes
and Message Navigation. The .txt file includes the plain ASCII version
of the MurphyMoose-List Digest and can be viewed with a generic text editor
such as Notepad or with a web browser.

HTML Version:

http://www.matronics.com/digest/digestview.php?Style=82701&View=htm
l&Chapter 16-07-21&Archive=MurphyMoose

Text Version:

http://www.matronics.com/digest/digestview.php?Style=82701&View=txt
&Chapter 16-07-21&Archive=MurphyMoose


========================
=======================
EMail Version of Today's List Digest Archive
========================
=======================


----------------------------------------------------------
  MurphyMoose-List Digest Archive
  ---
  Total Messages Posted Thu 07/21/16: 1
----------------------------------------------------------


Today's Message Index:
----------------------

1. 06:28 PM - Moose flaps (jgoodwin)


________________________________ Message 1 ______________________________
_______


Time: 06:28:20 PM PST US
Subject: Moose flaps
From: "jgoodwin" <goody989(at)msn.com>


My build manual states flap travel of 39 degrees. Not even close; regardles
s of
reflex, 27 to 32 is all I get. Has anyone else found interference with the
flap
retract horns and the bulkhead/doorposts? (This interference does not affec
t
the travel.)
Unrelated; my exhaust is at least 5 inches too short to clear the lower co
wling...


Read this topic online here:

http://forums.matronics.com/viewtopic.php?p=458505#458505





===========
se-List Email Forum -
hyMoose-List">http://www.matronics.com/Navigator?MurphyMoose-List
===========
p; - MATRONICS WEB FORUMS -
ums.matronics.com
===========
p; - NEW MATRONICS LIST WIKI -
matronics.com
===========
p; - List Contribution Web Site -
p;   -Matt Dralle, List Admin.
http://www.matronics.com/contribution
===========


- The Matronics MurphyMoose-List Email Forum -
 

Use the List Feature Navigator to browse the many List utilities available such as the Email Subscriptions page, Archive Search & Download, 7-Day Browse, Chat, FAQ, Photoshare, and much more:

http://www.matronics.com/Navigator?MurphyMoose-List
Back to top
Display posts from previous:   
Post new topic   Reply to topic    Matronics Email Lists Forum Index -> MurphyMoose-List All times are GMT - 8 Hours
Page 1 of 1

 
Jump to:  
You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot vote in polls in this forum
You cannot attach files in this forum
You can download files in this forum


Powered by phpBB © 2001, 2005 phpBB Group