Matronics Email Lists Forum Index Matronics Email Lists
Web Forum Interface to the Matronics Email Lists
 
 Get Email Distribution Too!Get Email Distribution Too!    FAQFAQ   SearchSearch   MemberlistMemberlist   UsergroupsUsergroups   RegisterRegister 
 ProfileProfile   Log in to check your private messagesLog in to check your private messages   Log inLog in 

engine support

 
Post new topic   Reply to topic    Matronics Email Lists Forum Index -> Europa-List
View previous topic :: View next topic  
Author Message
mp.gamble(at)talktalk.net
Guest





PostPosted: Tue May 16, 2017 12:07 am    Post subject: engine support Reply with quote

Can anyone tell me what tool is needed to fit the 4 engine support bolts – 912S engine mount to block?
Thanks
Mike Gamble
Mono XS
G-CFMP


- The Matronics Europa-List Email Forum -
 

Use the List Feature Navigator to browse the many List utilities available such as the Email Subscriptions page, Archive Search & Download, 7-Day Browse, Chat, FAQ, Photoshare, and much more:

http://www.matronics.com/Navigator?Europa-List
Back to top
JonathanMilbank



Joined: 14 Apr 2012
Posts: 383
Location: Aberdeen area

PostPosted: Tue May 16, 2017 2:10 am    Post subject: Re: engine support Reply with quote

I used an Allen key/wrench for mine. Additionally you'll probably need to temporarily remove one of the inlet manifolds and maybe even a coolant elbow pipe connector on one of the cylinder heads to get access to one of the bolts.

You'll probably also find that you need to slide a metal tube/pipe of some sort over the end of the Allen key to get leverage for tightening.


- The Matronics Europa-List Email Forum -
 

Use the List Feature Navigator to browse the many List utilities available such as the Email Subscriptions page, Archive Search & Download, 7-Day Browse, Chat, FAQ, Photoshare, and much more:

http://www.matronics.com/Navigator?Europa-List
Back to top
View user's profile Send private message
pjeffers(at)talktalk.net
Guest





PostPosted: Tue May 16, 2017 11:56 pm    Post subject: engine support Reply with quote

Hi Mike,
You just need an Allen Key of the correct size but you will need one that is long enough to reach, in particular, the ones on the LHS of the engine.
I am afraid you will need to go to a good tool shop. An alternative that I use is a correct size key bit on the end of an extension rod. In order to keep the diameter as small as possible use 1/4" square drive extension.
Pete

From: owner-europa-list-server(at)matronics.com [mailto:owner-europa-list-server(at)matronics.com] On Behalf Of mp.gamble
Sent: 16 May 2017 09:07
To: europa-list(at)matronics.com
Subject: engine support

Can anyone tell me what tool is needed to fit the 4 engine support bolts – 912S engine mount to block?
Thanks
Mike Gamble
Mono XS
G-CFMP


Virus-free. www.avg.com


- The Matronics Europa-List Email Forum -
 

Use the List Feature Navigator to browse the many List utilities available such as the Email Subscriptions page, Archive Search & Download, 7-Day Browse, Chat, FAQ, Photoshare, and much more:

http://www.matronics.com/Navigator?Europa-List
Back to top
mp.gamble(at)talktalk.net
Guest





PostPosted: Wed May 17, 2017 9:02 am    Post subject: engine support Reply with quote

Right Pete but what size key bit is needed? I have the 1/4 ‘’ extension.
Thanks
Mike


- The Matronics Europa-List Email Forum -
 

Use the List Feature Navigator to browse the many List utilities available such as the Email Subscriptions page, Archive Search & Download, 7-Day Browse, Chat, FAQ, Photoshare, and much more:

http://www.matronics.com/Navigator?Europa-List
Back to top
Nigel Graham



Joined: 23 Mar 2017
Posts: 36
Location: Winchester - UK

PostPosted: Fri May 19, 2017 6:53 am    Post subject: Re: engine support Reply with quote

Mike, you need an 8.0 mm hex. If you need to buy the tool, look for one with a spherically ground tip - it will allow you to tighten the hex head Allen bolts from a slight angle (up to about 10 degrees I think) which is useful if you can't get a "straight in approach" to the little blighters!

- The Matronics Europa-List Email Forum -
 

Use the List Feature Navigator to browse the many List utilities available such as the Email Subscriptions page, Archive Search & Download, 7-Day Browse, Chat, FAQ, Photoshare, and much more:

http://www.matronics.com/Navigator?Europa-List
Back to top
View user's profile Send private message
mp.gamble(at)talktalk.net
Guest





PostPosted: Thu May 25, 2017 9:10 am    Post subject: engine support Reply with quote

Thanks Nigel. A straight in approach it isn't but we will manage.
Mike

--


- The Matronics Europa-List Email Forum -
 

Use the List Feature Navigator to browse the many List utilities available such as the Email Subscriptions page, Archive Search & Download, 7-Day Browse, Chat, FAQ, Photoshare, and much more:

http://www.matronics.com/Navigator?Europa-List
Back to top
Display posts from previous:   
Post new topic   Reply to topic    Matronics Email Lists Forum Index -> Europa-List All times are GMT - 8 Hours
Page 1 of 1

 
Jump to:  
You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot vote in polls in this forum
You cannot attach files in this forum
You can download files in this forum


Powered by phpBB © 2001, 2005 phpBB Group