Matronics Email Lists Forum Index Matronics Email Lists
BBS Forum Interface to the Matronics Email Lists
 
 Get Email Distribution Too!Get Email Distribution Too!    FAQFAQ   SearchSearch   MemberlistMemberlist   UsergroupsUsergroups   RegisterRegister 
 ProfileProfile   Log in to check your private messagesLog in to check your private messages   Log inLog in 

Prop cover plate

 
Post new topic   Reply to topic    Matronics Email Lists Forum Index -> Pietenpol-List
View previous topic :: View next topic  
Author Message
Rick Schreiber



Joined: 16 Jan 2008
Posts: 346

PostPosted: Tue May 23, 2017 7:37 am    Post subject: Prop cover plate Reply with quote

I'm thinking about having a number of prop cover plates made with an acid etched design on the surface. This is just a thin cover plate meant to be used over a standard steel or aluminum prop plate. The diameter will be around 6" and made for a SAE-1 bolt pattern as used on a corvair prop hub. I need to run at least 25 of these to make it worthwhile. The cost is about $10 each. If there is enough interest I will have these made. Just send me a pm at lmforge at earthlink.net if interested. The attached picture is a paper print of the graphic taped to the front of my Piet/corvair. The plate will be marked for the prop bolt holes but will not be drilled or cut out. I want to get these done before Brodhead so I'll need to hear from those interested soon.
Rick Schreiber
NX478RS
Valparaiso, IN


- The Matronics Pietenpol-List Email Forum -
 

Use the List Feature Navigator to browse the many List utilities available such as the Email Subscriptions page, Archive Search & Download, 7-Day Browse, Chat, FAQ, Photoshare, and much more:

http://www.matronics.com/Navigator?Pietenpol-List



prop-plate.jpg
 Description:
 Filesize:  45.4 KB
 Viewed:  792 Time(s)

prop-plate.jpg


Back to top
View user's profile Send private message Send e-mail
taildrags



Joined: 29 Dec 2009
Posts: 1546
Location: Medford, OR

PostPosted: Tue May 23, 2017 7:06 pm    Post subject: Re: Prop cover plate Reply with quote

Nice design! I'm guessing the Ford builders will be especially interested in these for the period look that they impart. My A75 sports a thin aluminum reproduction of the original Continental plate, which I think I got from Wag Aero or someplace. I don't remember what it cost. It, too, is decorative and goes over the real crush plate. Obviously, those who are using tapered shaft prop hubs will be out of luck with something like this, although I guess you could also design a plate with the graphics positioned around where the nose of the hub pokes through.

- The Matronics Pietenpol-List Email Forum -
 

Use the List Feature Navigator to browse the many List utilities available such as the Email Subscriptions page, Archive Search & Download, 7-Day Browse, Chat, FAQ, Photoshare, and much more:

http://www.matronics.com/Navigator?Pietenpol-List

_________________
Oscar Zuniga
Medford, OR
Air Camper NX41CC "Scout"
A75 power, 72x36 Culver prop
Back to top
View user's profile Send private message Send e-mail Visit poster's website
Rick Schreiber



Joined: 16 Jan 2008
Posts: 346

PostPosted: Thu May 25, 2017 3:46 pm    Post subject: Re: Prop cover plate Reply with quote

Thanks for the compliment Oscar. So far the response has been pretty good. I may wind up doing more than 25 so I will have enough to take to Brodhead.

Rick Schreiber
NX478RS


- The Matronics Pietenpol-List Email Forum -
 

Use the List Feature Navigator to browse the many List utilities available such as the Email Subscriptions page, Archive Search & Download, 7-Day Browse, Chat, FAQ, Photoshare, and much more:

http://www.matronics.com/Navigator?Pietenpol-List
Back to top
View user's profile Send private message Send e-mail
suttonmark56(at)gmail.com
Guest





PostPosted: Thu May 25, 2017 6:22 pm    Post subject: Prop cover plate Reply with quote

On Thu, May 25, 2017 at 7:49 PM Rick Schreiber <lmforge(at)earthlink.net (lmforge(at)earthlink.net)> wrote:

Quote:
--> Pietenpol-List message posted by: "Rick Schreiber" <lmforge(at)earthlink.net (lmforge(at)earthlink.net)>

Thanks for the compliment Oscar. So far the response has been pretty good. I may wind up doing more than 25 so I will have enough to take to Brodhead.

Rick Schreiber
NX478RS




Read this topic online here:

http://forums.matronics.com/viewtopic.php?p=469610#469610




I would love to purchase one from too if you have enough 


Mark Sutton
678/283-4250
Quote:


===========
br> enpol-List" rel="noreferrer" target="_blank">http://www.matronics.com/Navigator?Pietenpol-List
===========
FORUMS -
eferrer" target="_blank">http://forums.matronics.com
===========
WIKI -
errer" target="_blank">http://wiki.matronics.com
===========
b Site -
          -Matt Dralle, List Admin.
rel="noreferrer" target="_blank">http://www.matronics.com/contribution
===========





- The Matronics Pietenpol-List Email Forum -
 

Use the List Feature Navigator to browse the many List utilities available such as the Email Subscriptions page, Archive Search & Download, 7-Day Browse, Chat, FAQ, Photoshare, and much more:

http://www.matronics.com/Navigator?Pietenpol-List
Back to top
Display posts from previous:   
Post new topic   Reply to topic    Matronics Email Lists Forum Index -> Pietenpol-List All times are GMT - 8 Hours
Page 1 of 1

 
Jump to:  
You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot vote in polls in this forum
You cannot attach files in this forum
You can download files in this forum


Powered by phpBB © 2001, 2005 phpBB Group