Matronics Email Lists Forum Index Matronics Email Lists
Web Forum Interface to the Matronics Email Lists
 
 Get Email Distribution Too!Get Email Distribution Too!    FAQFAQ   SearchSearch   MemberlistMemberlist   UsergroupsUsergroups   RegisterRegister 
 ProfileProfile   Log in to check your private messagesLog in to check your private messages   Log inLog in 

Tightening the stainless steel nipple on the carburetor

 
Post new topic   Reply to topic    Matronics Email Lists Forum Index -> Europa-List
View previous topic :: View next topic  
Author Message
paul.the.aviator(at)gmail
Guest





PostPosted: Mon Jul 17, 2017 1:56 pm    Post subject: Tightening the stainless steel nipple on the carburetor Reply with quote

Hi all,
 
I’m looking for a best practice.  I want to overhaul the carburetors on my Rotax 914 and every time I have found this challenging.  I find tightening the stainless steel line nipple onto the carburetor difficult.  
I can't get a tool in the tight space and I have even tried making my own tool without success.
 
Does Rotax have a special spanner (wrench for you Americans) for this? Any tips would be appreciated.
 
Paul


- The Matronics Europa-List Email Forum -
 

Use the List Feature Navigator to browse the many List utilities available such as the Email Subscriptions page, Archive Search & Download, 7-Day Browse, Chat, FAQ, Photoshare, and much more:

http://www.matronics.com/Navigator?Europa-List
Back to top
h&jeuropa



Joined: 07 Nov 2006
Posts: 634

PostPosted: Tue Jul 18, 2017 3:46 am    Post subject: Re: Tightening the stainless steel nipple on the carburetor Reply with quote

Hi Paul,

Bud Yerly's advice is to disconnect the SS lines at the fuel pressure regulator, rather than at the carbs. That seems to work fine.

Jim


- The Matronics Europa-List Email Forum -
 

Use the List Feature Navigator to browse the many List utilities available such as the Email Subscriptions page, Archive Search & Download, 7-Day Browse, Chat, FAQ, Photoshare, and much more:

http://www.matronics.com/Navigator?Europa-List
Back to top
View user's profile Send private message
paul.the.aviator(at)gmail
Guest





PostPosted: Fri Jul 21, 2017 8:13 am    Post subject: Tightening the stainless steel nipple on the carburetor Reply with quote

I guess that is one approach. I like to send my carbs to Lockwood and I happen to have a second set so I just do an exchange.  

So... I guess I'm still looking to understand how folks tighten the SS nipples in place 
On Tue, Jul 18, 2017 at 6:46 AM, h&amp;jeuropa <butcher43(at)att.net (butcher43(at)att.net)> wrote:
Quote:
--> Europa-List message posted by: "h&amp;jeuropa" <butcher43(at)att.net (butcher43(at)att.net)>

Hi Paul,

Bud Yerly's advice is to disconnect the SS lines at the fuel pressure regulator, rather than at the carbs.  That seems to work fine.

Jim




Read this topic online here:

http://forums.matronics.com/viewtopic.php?p=471129#471129






====================================
pa-List" rel="noreferrer" target="_blank">http://www.matronics.com/Navigator?Europa-List
====================================
FORUMS -
eferrer" target="_blank">http://forums.matronics.com
====================================
WIKI -
errer" target="_blank">http://wiki.matronics.com
====================================
b Site -
          -Matt Dralle, List Admin.
rel="noreferrer" target="_blank">http://www.matronics.com/contribution
====================================





- The Matronics Europa-List Email Forum -
 

Use the List Feature Navigator to browse the many List utilities available such as the Email Subscriptions page, Archive Search & Download, 7-Day Browse, Chat, FAQ, Photoshare, and much more:

http://www.matronics.com/Navigator?Europa-List
Back to top
Ivor



Joined: 23 Jul 2015
Posts: 51

PostPosted: Fri Jul 21, 2017 11:15 am    Post subject: Re: Tightening the stainless steel nipple on the carburetor Reply with quote

I have successfully used a 14 mm crowfoot and 14 mm half ring spanner
( wrench). specifically the half ring spanner is a ring spanner with a slot cut into it to allow fitment over the pipe, It's a bit tight but works for me,


- The Matronics Europa-List Email Forum -
 

Use the List Feature Navigator to browse the many List utilities available such as the Email Subscriptions page, Archive Search & Download, 7-Day Browse, Chat, FAQ, Photoshare, and much more:

http://www.matronics.com/Navigator?Europa-List
Back to top
View user's profile Send private message
Display posts from previous:   
Post new topic   Reply to topic    Matronics Email Lists Forum Index -> Europa-List All times are GMT - 8 Hours
Page 1 of 1

 
Jump to:  
You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot vote in polls in this forum
You cannot attach files in this forum
You can download files in this forum


Powered by phpBB © 2001, 2005 phpBB Group