Matronics Email Lists Forum Index Matronics Email Lists
Web Forum Interface to the Matronics Email Lists
 
 Get Email Distribution Too!Get Email Distribution Too!    FAQFAQ   SearchSearch   MemberlistMemberlist   UsergroupsUsergroups   RegisterRegister 
 ProfileProfile   Log in to check your private messagesLog in to check your private messages   Log inLog in 

F-1046 Longeron to F-1005E Gusset Holes

 
Post new topic   Reply to topic    Matronics Email Lists Forum Index -> RV10-List
View previous topic :: View next topic  
Author Message
flyboy(at)gmail.com
Guest





PostPosted: Tue Jul 04, 2017 2:16 pm    Post subject: F-1046 Longeron to F-1005E Gusset Holes Reply with quote

I lined up the F-1046L longeron with the gusset as described on page 29-9, with the longeron flush with the skin. Then, I drilled the holes. The edge distance is terrible, but I can't see what I did wrong. I've searched and found others with the same problem, but no resolutions turn up. The diagram on 29-9 sure acts like these holes will wind up in the middle of the longeron, but I don't see how.
Waiting to drill the other side until I can figure out how to avoid the same problem. Looks to me like I should replace the longeron, but I don't know how to do it any differently and still have the longeron flush with the skin.
https://goo.gl/photos/J8s8gheQ1GBmUUi1A
https://goo.gl/photos/z11vaX6PZt3Zc1w69
Any suggestions?


- The Matronics RV10-List Email Forum -
 

Use the List Feature Navigator to browse the many List utilities available such as the Email Subscriptions page, Archive Search & Download, 7-Day Browse, Chat, FAQ, Photoshare, and much more:

http://www.matronics.com/Navigator?RV10-List
Back to top
philperry9



Joined: 23 Nov 2011
Posts: 379

PostPosted: Tue Jul 04, 2017 6:26 pm    Post subject: F-1046 Longeron to F-1005E Gusset Holes Reply with quote

I don't think you need to rebuild the longeron. Give Vans a call tomorrow and send them the photos too.   I believe they have developed a repair for this. IIRC, it involves a gusset. But give them a shout and I'm pretty sure they'll be able to take care of you.
At least you noticed it now. Some folks have built on and had to correct it later after the tail is assembled.  Only to have to tear it back apart to fix it.

Sent from my iPhone

On Jul 4, 2017, at 4:16 PM, Berck E. Nash <flyboy(at)gmail.com (flyboy(at)gmail.com)> wrote:
Quote:
I lined up the F-1046L longeron with the gusset as described on page 29-9, with the longeron flush with the skin. Then, I drilled the holes. The edge distance is terrible, but I can't see what I did wrong. I've searched and found others with the same problem, but no resolutions turn up. The diagram on 29-9 sure acts like these holes will wind up in the middle of the longeron, but I don't see how.
Waiting to drill the other side until I can figure out how to avoid the same problem. Looks to me like I should replace the longeron, but I don't know how to do it any differently and still have the longeron flush with the skin.
https://goo.gl/photos/J8s8gheQ1GBmUUi1A
https://goo.gl/photos/z11vaX6PZt3Zc1w69
Any suggestions?




- The Matronics RV10-List Email Forum -
 

Use the List Feature Navigator to browse the many List utilities available such as the Email Subscriptions page, Archive Search & Download, 7-Day Browse, Chat, FAQ, Photoshare, and much more:

http://www.matronics.com/Navigator?RV10-List
Back to top
View user's profile Send private message
flyboy(at)gmail.com
Guest





PostPosted: Wed Jul 05, 2017 10:05 am    Post subject: F-1046 Longeron to F-1005E Gusset Holes Reply with quote

Thanks, I've got an e-mail out to them with the photos, I'll let you know what they send back.

Rebuilding the longeron isn't a big deal.  Heck, I can probably bend this one in under half an hour after all the practice with the first four.  The bigger deal is that after I build it, I'm not sure what to do to fix the problem.  I can line the longeron up so that the holes in the gusset are in the middle, but that's going to create quite a gap to the skins.  It looks like a similar situation on the other side.

On Tue, Jul 4, 2017 at 8:25 PM, Phillip Perry <philperry9(at)gmail.com (philperry9(at)gmail.com)> wrote:
Quote:
I don't think you need to rebuild the longeron.   Give Vans a call tomorrow and send them the photos too.   I believe they have developed a repair for this.    IIRC, it involves a gusset.   But give them a shout and I'm pretty sure they'll be able to take care of you. 
At least you noticed it now.   Some folks have built on and had to correct it later after the tail is assembled.  Only to have to tear it back apart to fix it. 

Sent from my iPhone

On Jul 4, 2017, at 4:16 PM, Berck E. Nash <flyboy(at)gmail.com (flyboy(at)gmail.com)> wrote:
Quote:
I lined up the F-1046L longeron with the gusset as described on page 29-9, with the longeron flush with the skin. Then, I drilled the holes. The edge distance is terrible, but I can't see what I did wrong. I've searched and found others with the same problem, but no resolutions turn up. The diagram on 29-9 sure acts like these holes will wind up in the middle of the longeron, but I don't see how.
Waiting to drill the other side until I can figure out how to avoid the same problem. Looks to me like I should replace the longeron, but I don't know how to do it any differently and still have the longeron flush with the skin.
https://goo.gl/photos/J8s8gheQ1GBmUUi1A
https://goo.gl/photos/z11vaX6PZt3Zc1w69
Any suggestions?





- The Matronics RV10-List Email Forum -
 

Use the List Feature Navigator to browse the many List utilities available such as the Email Subscriptions page, Archive Search & Download, 7-Day Browse, Chat, FAQ, Photoshare, and much more:

http://www.matronics.com/Navigator?RV10-List
Back to top
kearney



Joined: 20 Sep 2008
Posts: 563

PostPosted: Sat Jul 08, 2017 3:35 pm    Post subject: Re: F-1046 Longeron to F-1005E Gusset Holes Reply with quote

Hi

I was reading this thread with some interest as I was about to do this step as well.

Prior to drilling I marked where the holes would be using a sharpie through the gusset holes. The edge distance was not good for the aft most holes.
The source of the problem was that the flange of the gusset was not parallel to the skin / longeron.

I was think of using a shim to move the longeron inboard but then realized there was a much simpler solution.

If you rotate the F-1005C you can get the gusset flange to line up parallel to the skin. This will give good edge distance. You will need to rotate the F1005 beyond where you want it a sit will spring back a little.

Cheers

Les

C-GCWZ Flying
C-GROK some assembly required


- The Matronics RV10-List Email Forum -
 

Use the List Feature Navigator to browse the many List utilities available such as the Email Subscriptions page, Archive Search & Download, 7-Day Browse, Chat, FAQ, Photoshare, and much more:

http://www.matronics.com/Navigator?RV10-List
Back to top
View user's profile Send private message
flyboy(at)gmail.com
Guest





PostPosted: Sun Jul 09, 2017 5:48 pm    Post subject: F-1046 Longeron to F-1005E Gusset Holes Reply with quote

Thanks, I eventually came to the same conclusion.  Vans wrote back and said they didn't know what caused the problem, but that I could just add a doubler.  That didn't seem like a reasonable solution to me. Sure, I could add a doubler and put new holes in the longeron, but the new holes through the doubler would have bad edge distance in the gusset.  I could add more holes way out in the gusset, but this wasn't satisfying to me, either.
After spending a lot of time playing with the parts and a sharpie, I realized what you did, that I could pivot the gusset outboard and fix the edge distance.  For the right side (which I hadn't drilled yet), I went ahead and drilled through the side skin in the forward-most hole into the longeron so I could cleco to the skin and be sure that alignment was correct.  Then, I simply squeezed the gusset inboard with my hands and drilled the aft-most hole first.  Put a cleco in it, and drilled the rest.  I think they came out just fine.
So, I rebuilt the left longeron with the bad holes (probably took me about the same amount of time as making a doubler from scratch, figuring out rivet lengths, etc, would have taken).  Drilled the new longeron with my new technique and I think it too is now fine.
https://goo.gl/photos/t63mDsvT4a5nmDFu5
https://goo.gl/photos/bgZw1QuKYaSiWZLS8

So, a note to anyone else who hasn't yet done this: check your edge distance before drilling these holes (particularly on the aft-most hole), and note that you can pull the gusset outboard as necessary to get the right edge distance.
On Sat, Jul 8, 2017 at 5:35 PM, kearney <kearney(at)shaw.ca (kearney(at)shaw.ca)> wrote:
Quote:
--> RV10-List message posted by: "kearney" <kearney(at)shaw.ca (kearney(at)shaw.ca)>

Hi

I was reading this thread with some interest as I was about to do this step as well.

Prior to drilling I marked where the holes would be using a sharpie through the gusset holes. The edge distance was not good for the aft most holes.
The source of the problem was that the flange of the gusset was not parallel to the skin / longeron.

I was think of using a shim to move the longeron inboard but then realized there was a much simpler solution.

If you rotate the F-1005C you can get the gusset flange to line up parallel to the skin. This will give good edge distance. You will need to rotate the F1005 beyond where you want it a sit will spring back a little.

Cheers

Les

C-GCWZ Flying
C-GROK some assembly required




Read this topic online here:

http://forums.matronics.com/viewtopic.php?p=470800#470800






====================================
-List" rel="noreferrer" target="_blank">http://www.matronics.com/Navigator?RV10-List
====================================
FORUMS -
eferrer" target="_blank">http://forums.matronics.com
====================================
WIKI -
errer" target="_blank">http://wiki.matronics.com
====================================
b Site -
          -Matt Dralle, List Admin.
rel="noreferrer" target="_blank">http://www.matronics.com/contribution
====================================





- The Matronics RV10-List Email Forum -
 

Use the List Feature Navigator to browse the many List utilities available such as the Email Subscriptions page, Archive Search & Download, 7-Day Browse, Chat, FAQ, Photoshare, and much more:

http://www.matronics.com/Navigator?RV10-List
Back to top
Mauledriver(at)nc.rr.com
Guest





PostPosted: Thu Jul 20, 2017 2:09 pm    Post subject: F-1046 Longeron to F-1005E Gusset Holes Reply with quote

On 7/4/2017 6:16 PM, Berck E. Nash wrote:
On related note; I would recommend that builders apply corrosion
protection (primer, alodine) to the longeron, particularly where it
joins to the skin.

Vans is very conservative with specifying areas where they recommend
priming and I don't recall if this is one of those areas. Many builders
are obsessive about priming and will certainly prime/alodine it. I
missed this one and had to take some action to stop some filiform
corrosion developing at that joint.

Bill "in no way, shape or form is trying to restart any version of the
primer wars" Watson

Quote:
I lined up the F-1046L longeron with the gusset as described on page
29-9, with the longeron flush with the skin. Then, I drilled the
holes. The edge distance is terrible, but I can't see what I did
wrong. I've searched and found others with the same problem, but no
resolutions turn up. The diagram on 29-9 sure acts like these holes
will wind up in the middle of the longeron, but I don't see how.

Waiting to drill the other side until I can figure out how to avoid
the same problem. Looks to me like I should replace the longeron, but
I don't know how to do it any differently and still have the longeron
flush with the skin.

https://goo.gl/photos/J8s8gheQ1GBmUUi1A
https://goo.gl/photos/z11vaX6PZt3Zc1w69

Any suggestions?

---
This email has been checked for viruses by Avast antivirus software.
https://www.avast.com/antivirus


- The Matronics RV10-List Email Forum -
 

Use the List Feature Navigator to browse the many List utilities available such as the Email Subscriptions page, Archive Search & Download, 7-Day Browse, Chat, FAQ, Photoshare, and much more:

http://www.matronics.com/Navigator?RV10-List
Back to top
flyboy(at)gmail.com
Guest





PostPosted: Thu Jul 20, 2017 6:58 pm    Post subject: F-1046 Longeron to F-1005E Gusset Holes Reply with quote

Thanks, good call. Vans does specifically call out priming the longerons.  First, in section 5, they specifically say to prime all angle, as it's not alclad.  Then, in section 29, it specifically says to prime the longerons, then other parts as desired.

I'm not priming anything Van's doesn't say to prime, but I did miss the aluminum angle in the tail cone, so I'm going to go back and do it.

Berck (feeling like he missed out, since he started building too late to join the primer wars)

On Thu, Jul 20, 2017 at 4:09 PM, Bill Watson <Mauledriver(at)nc.rr.com (Mauledriver(at)nc.rr.com)> wrote:
Quote:
--> RV10-List message posted by: Bill Watson <Mauledriver(at)nc.rr.com (Mauledriver(at)nc.rr.com)>

On 7/4/2017 6:16 PM, Berck E. Nash wrote:
On related note; I would recommend that builders apply corrosion protection (primer, alodine) to the longeron, particularly  where it joins to the skin.

Vans is very conservative with specifying areas where they recommend priming and I don't recall if this is one of those areas.  Many builders are obsessive about priming and will certainly prime/alodine it.  I missed this one and had to take some action to stop some filiform corrosion developing at that joint.

Bill "in no way, shape or form is trying to restart any version of the primer wars" Watson

Quote:
I lined up the F-1046L longeron with the gusset as described on page 29-9, with the longeron flush with the skin. Then, I drilled the holes. The edge distance is terrible, but I can't see what I did wrong. I've searched and found others with the same problem, but no resolutions turn up. The diagram on 29-9 sure acts like these holes will wind up in the middle of the longeron, but I don't see how.

Waiting to drill the other side until I can figure out how to avoid the same problem. Looks to me like I should replace the longeron, but I don't know how to do it any differently and still have the longeron flush with the skin.

https://goo.gl/photos/J8s8gheQ1GBmUUi1A
https://goo.gl/photos/z11vaX6PZt3Zc1w69

Any suggestions?



---
This email has been checked for viruses by Avast antivirus software.
https://www.avast.com/antivirus

====================================
-List" rel="noreferrer" target="_blank">http://www.matronics.com/Navigator?RV10-List
====================================
FORUMS -
eferrer" target="_blank">http://forums.matronics.com
====================================
WIKI -
errer" target="_blank">http://wiki.matronics.com
====================================
b Site -
          -Matt Dralle, List Admin.
rel="noreferrer" target="_blank">http://www.matronics.com/contribution
====================================





- The Matronics RV10-List Email Forum -
 

Use the List Feature Navigator to browse the many List utilities available such as the Email Subscriptions page, Archive Search & Download, 7-Day Browse, Chat, FAQ, Photoshare, and much more:

http://www.matronics.com/Navigator?RV10-List
Back to top
Display posts from previous:   
Post new topic   Reply to topic    Matronics Email Lists Forum Index -> RV10-List All times are GMT - 8 Hours
Page 1 of 1

 
Jump to:  
You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot vote in polls in this forum
You cannot attach files in this forum
You can download files in this forum


Powered by phpBB © 2001, 2005 phpBB Group