Matronics Email Lists Forum Index Matronics Email Lists
Web Forum Interface to the Matronics Email Lists
 
 Get Email Distribution Too!Get Email Distribution Too!    FAQFAQ   SearchSearch   MemberlistMemberlist   UsergroupsUsergroups   RegisterRegister 
 ProfileProfile   Log in to check your private messagesLog in to check your private messages   Log inLog in 

Flap motor safety wire hole

 
Post new topic   Reply to topic    Matronics Email Lists Forum Index -> RV10-List
View previous topic :: View next topic  
Author Message
dfritz(at)bpgsim.com
Guest





PostPosted: Mon Nov 06, 2017 4:29 pm    Post subject: Flap motor safety wire hole Reply with quote

Does anyone have a good tip for drilling the safety wire hole in the
barrel of the flap motor.  The instructions say do not remove the end as
it is factory set.  However I would think keeping track of the number of
turns it is unscrewed should be easy to do. Drilling with a 1/16" drill
into steel seems like a good way to buy drill bits.  Am I stressing over
a mole hill?

David


- The Matronics RV10-List Email Forum -
 

Use the List Feature Navigator to browse the many List utilities available such as the Email Subscriptions page, Archive Search & Download, 7-Day Browse, Chat, FAQ, Photoshare, and much more:

http://www.matronics.com/Navigator?RV10-List
Back to top
larkrv10(at)gmail.com
Guest





PostPosted: Mon Nov 06, 2017 5:04 pm    Post subject: Flap motor safety wire hole Reply with quote

David just go nice  and steady, slow etc with a new bit.  Shouldn’t be a problem at all.
Rick
#40956
C-GDMH

Sent from Mail for Windows 10

From: David J. Fritzsche (dfritz(at)bpgsim.com)
Sent: November 6, 2017 7:32 PM
To: RV-10 Matronics (rv10-list(at)matronics.com)
Subject: Flap motor safety wire hole


--> RV10-List message posted by: "David J. Fritzsche" <dfritz(at)bpgsim.com>


Does anyone have a good tip for drilling the safety wire hole in the
barrel of the flap motor. The instructions say do not remove the end as
it is factory set. However I would think keeping track of the number of
turns it is unscrewed should be easy to do. Drilling with a 1/16" drill
into steel seems like a good way to buy drill bits. Am I stressing over
a mole hill?

David

_         - NEW MATRONICS LIST WI======================

_=                              -Matt Dralle, List Admin.


- The Matronics RV10-List Email Forum -
 

Use the List Feature Navigator to browse the many List utilities available such as the Email Subscriptions page, Archive Search & Download, 7-Day Browse, Chat, FAQ, Photoshare, and much more:

http://www.matronics.com/Navigator?RV10-List
Back to top
Greg McFarlane



Joined: 12 Apr 2012
Posts: 57
Location: Albany Western Australia

PostPosted: Tue Nov 07, 2017 2:33 am    Post subject: Re: Flap motor safety wire hole Reply with quote

To Comply with SB 07-4-12 ....... I drilled straight in (parallel to jackscrew) just to clear the rod end safety jam nut about 5/16 then vertically down to capture the previous hole. That minimised the chance of bursting out trying to drill an angled hole. As well as the safety wire, most over here are also making a small ally fitting of appropriate gauge to lay alongside the jackscrew and the rod end, with a hole large enough to allow the normal tightening of flap bolt on the rod end ball, then at the jackscrew end, bent to go around the jackscrew and secured with a clamp. Might be overkill but that’s what is being done. Cheers from Western Australia 🇦🇺

- The Matronics RV10-List Email Forum -
 

Use the List Feature Navigator to browse the many List utilities available such as the Email Subscriptions page, Archive Search & Download, 7-Day Browse, Chat, FAQ, Photoshare, and much more:

http://www.matronics.com/Navigator?RV10-List
Back to top
View user's profile Send private message
glastar(at)gmx.net
Guest





PostPosted: Tue Nov 07, 2017 5:42 am    Post subject: Flap motor safety wire hole Reply with quote

Greg, any picture Smile

On 07.11.2017 11:33, Greg McFarlane wrote:
Quote:


To Comply with SB 07-4-12 ....... I drilled straight in (parallel to jackscrew) just to clear the rod end safety jam nut about 5/16 then vertically down to capture the previous hole. That minimised the chance of bursting out trying to drill an angled hole. As well as the safety wire, most over here are also making a small ally fitting of appropriate gauge to lay alongside the jackscrew and the rod end, with a hole large enough to allow the normal tightening of flap bolt on the rod end ball, then at the jackscrew end, bent to go around the jackscrew and secured with a clamp. Might be overkill but that’s what is being done. Cheers from Western Australia 🇦🇺



- The Matronics RV10-List Email Forum -
 

Use the List Feature Navigator to browse the many List utilities available such as the Email Subscriptions page, Archive Search & Download, 7-Day Browse, Chat, FAQ, Photoshare, and much more:

http://www.matronics.com/Navigator?RV10-List
Back to top
Greg McFarlane



Joined: 12 Apr 2012
Posts: 57
Location: Albany Western Australia

PostPosted: Tue Nov 07, 2017 8:52 pm    Post subject: Re: Flap motor safety wire hole Reply with quote

Unfortunately no picture, and a bit hard to get into the tunnel area to get one quickly Rolling Eyes However Ally fitting in length is about inch and half along jackscrew and long enough to allow a approx3/8 hole (hole, large enough fit over the spacer) in rod end——-end.............Width, wide enough to allow for the 3/8 hole at one end, and cut wider back at the jackscrew end to allow “tabs” to be bent/wrapped around the shaft for extra grip, then secured with a clamp, adele or hose. Same effect as safety wire in that if the rod end jam nut was to come loose then the jackscrew would be restrained from turning because the fitting is secured by the standard mounting bolt. Just needs to fit snug along rod end and jackscrew and not interfere with the normal flap operation, especially the normal tightening of the rod end bolt. Greg

- The Matronics RV10-List Email Forum -
 

Use the List Feature Navigator to browse the many List utilities available such as the Email Subscriptions page, Archive Search & Download, 7-Day Browse, Chat, FAQ, Photoshare, and much more:

http://www.matronics.com/Navigator?RV10-List
Back to top
View user's profile Send private message
Display posts from previous:   
Post new topic   Reply to topic    Matronics Email Lists Forum Index -> RV10-List All times are GMT - 8 Hours
Page 1 of 1

 
Jump to:  
You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot vote in polls in this forum
You cannot attach files in this forum
You can download files in this forum


Powered by phpBB © 2001, 2005 phpBB Group