Matronics Email Lists Forum Index Matronics Email Lists
Web Forum Interface to the Matronics Email Lists
 
 Get Email Distribution Too!Get Email Distribution Too!    FAQFAQ   SearchSearch   MemberlistMemberlist   UsergroupsUsergroups   RegisterRegister 
 ProfileProfile   Log in to check your private messagesLog in to check your private messages   Log inLog in 

Happy Thanksgiving!

 
Post new topic   Reply to topic    Matronics Email Lists Forum Index -> Kolb-List
View previous topic :: View next topic  
Author Message
Richard Pike



Joined: 09 Jan 2006
Posts: 1669
Location: Blountville, Tennessee

PostPosted: Thu Nov 23, 2017 3:02 pm    Post subject: Happy Thanksgiving! Reply with quote

Happy Thanksgiving to all the Kolbers and Kolbettes on the list, piddled with the FF a bit today and then took it flying for about 15 minutes. Had a good little breeze today, and up to now had only flown it in calm conditions. Flew good, ailerons are heavy as sin, feels way heavier than my MKIII, so the next part of the project will be to change the bellcrank arms for less throw and more leverage. Otherwise it flew fine.

The 277 now vibrates no more than any other 2 stroke above 5,000, and it is slightly worse but still acceptable from 4,500 to 5,000 so will quit worrying about that.

Also, on the other thread; Bill Sullivan asked about the effect of the exhaust pipe heating the wing fabric - now that the outlet is at the front I could hold my hand at the exhaust outlet and was quite surprised that at 6" away there is no heat at all. You have to get to within 2" before it starts to get hot. Wouldn't have guessed that.

It is supposed to get up to 60 tomorrow, so will rejet it a tad richer and try it again. The EGT kept flirting with 1200 today, that is a bit too hot.


- The Matronics Kolb-List Email Forum -
 

Use the List Feature Navigator to browse the many List utilities available such as the Email Subscriptions page, Archive Search & Download, 7-Day Browse, Chat, FAQ, Photoshare, and much more:

http://www.matronics.com/Navigator?Kolb-List

_________________
Richard Pike
Kolb MKIII N420P (420ldPoops)
Kingsport, TN 3TN0

Forgiving is tough, being forgiven is wonderful, and God's grace really is amazing.
Back to top
View user's profile Send private message Send e-mail Visit poster's website
victorbravo(at)sbcglobal.
Guest





PostPosted: Fri Nov 24, 2017 12:38 am    Post subject: Happy Thanksgiving! Reply with quote

Happy Turkey Day you turkeys ! Smile I hope everyone in the Kolb community had a wonderful and meaningful day today. We all have something to be thankful for.

Richard, if it is too chilly there, bring your airplane to Los Angeles to test fly it.... it was only 92 degrees here today!

Bill Berle
www.ezflaphandle.com  - safety & performance upgrade for light aircraft
www.grantstar.net           - winning proposals for non-profit and for-profit entities

--------------------------------------------
On Thu, 11/23/17, Richard Pike <thegreybaron(at)charter.net> wrote:

Subject: Happy Thanksgiving!
To: kolb-list(at)matronics.com
Date: Thursday, November 23, 2017, 3:02 PM


Pike" <thegreybaron(at)charter.net>

Happy Thanksgiving to all the Kolbers
and Kolbettes on the list, piddled with the FF a bit today
and then took it flying for about 15 minutes. Had a good
little breeze today, and up to now had only flown it in calm
conditions. Flew good, ailerons are heavy as sin, feels way
heavier than my MKIII, so the next part of the project will
be to change the bellcrank arms for less throw and more
leverage. Otherwise it flew fine.

The 277 now vibrates no more than any
other 2 stroke above 5,000, and it is slightly worse but
still acceptable from 4,500 to 5,000 so will quit worrying
about that.

Also, on the other thread; Bill
Sullivan asked about the effect of the exhaust pipe heating
the wing fabric - now that the outlet is at the front I
could hold my hand at the exhaust outlet and was quite
surprised that at 6" away there is no heat at all. You have
to get to within 2" before it starts to get hot. Wouldn't
have guessed that.

It is supposed to get up to 60
tomorrow, so will rejet it a tad richer and try it again.
The EGT kept flirting with 1200 today, that is a bit too
hot.

--------
Richard Pike
Kolb MKIII N420P (420ldPoops)
Kingsport, TN 3TN0

Forgiving is tough, being forgiven is
wonderful, and Grace really is amazing.




Read this topic online here:

http://forums.matronics.com/viewtopic.php?p=475482#475482






The Kolb-List Email Forum -
Navigator to browse
List Un/Subscription,
7-Day Browse, Chat, FAQ,
    - MATRONICS WEB FORUMS -
via the Web Forums!
    - NEW MATRONICS LIST WIKI -
Email List Wiki!
  - List Contribution Web Site -
support!
               
    -Matt Dralle, List Admin.


- The Matronics Kolb-List Email Forum -
 

Use the List Feature Navigator to browse the many List utilities available such as the Email Subscriptions page, Archive Search & Download, 7-Day Browse, Chat, FAQ, Photoshare, and much more:

http://www.matronics.com/Navigator?Kolb-List
Back to top
Richard Pike



Joined: 09 Jan 2006
Posts: 1669
Location: Blountville, Tennessee

PostPosted: Fri Nov 24, 2017 7:02 am    Post subject: Re: Happy Thanksgiving! Reply with quote

victorbravo(at)sbcglobal. wrote:
<snip> Richard, if it is too chilly there, bring your airplane to Los Angeles to test fly it.... it was only 92 degrees here today!

Bill Berle

<snip> NP; let me go change the jetting again...


- The Matronics Kolb-List Email Forum -
 

Use the List Feature Navigator to browse the many List utilities available such as the Email Subscriptions page, Archive Search & Download, 7-Day Browse, Chat, FAQ, Photoshare, and much more:

http://www.matronics.com/Navigator?Kolb-List

_________________
Richard Pike
Kolb MKIII N420P (420ldPoops)
Kingsport, TN 3TN0

Forgiving is tough, being forgiven is wonderful, and God's grace really is amazing.
Back to top
View user's profile Send private message Send e-mail Visit poster's website
Richard Pike



Joined: 09 Jan 2006
Posts: 1669
Location: Blountville, Tennessee

PostPosted: Fri Nov 24, 2017 4:33 pm    Post subject: Re: Happy Thanksgiving! Reply with quote

Got home this afternoon around 4:30, just enough time to swap in the next bigger main jet and go for a short hop before sunset. EGT's are ideal, barely nudges 1150 once in a while, the rest of the time stays around 1050-1100.

Lowered the nose and then BRAKKKKKK! Horrific racket from just above and behind my head, scared the fool out of me! Turned out the gap seal was weakened from where we cut it to fit the new muffler mount, and now whenever you get it over 50, it flutters. LOUDLY!

Anyway, now that the engine is behaving, I can work on a new gap seal.


- The Matronics Kolb-List Email Forum -
 

Use the List Feature Navigator to browse the many List utilities available such as the Email Subscriptions page, Archive Search & Download, 7-Day Browse, Chat, FAQ, Photoshare, and much more:

http://www.matronics.com/Navigator?Kolb-List

_________________
Richard Pike
Kolb MKIII N420P (420ldPoops)
Kingsport, TN 3TN0

Forgiving is tough, being forgiven is wonderful, and God's grace really is amazing.
Back to top
View user's profile Send private message Send e-mail Visit poster's website
williamtsullivan(at)att.n
Guest





PostPosted: Fri Nov 24, 2017 6:35 pm    Post subject: Happy Thanksgiving! Reply with quote

Before I let go of my Firestar, I made a gap seal out of a wide piece of flashing, reinforced with some hardware store aluminum angle. The front was secured with bolts and nylock nuts through the leading edge tubing extensions. There was a hinged piece that was cut out to go around the engine, and it could be flipped forward for fueling.
I had tried using fabric and velcro, but the glue on the velcro slipped out in the sun.

Bill Sullivan
--------------------------------------------
On Fri, 11/24/17, Richard Pike <thegreybaron(at)charter.net> wrote:



Lowered the nose and then BRAKKKKKK!
Horrific racket from just above and behind my head, scared
the fool out of me! Turned out the gap seal was weakened
from where we cut it to fit the new muffler mount, and now
whenever you get it over 50, it flutters. LOUDLY!

Anyway, now that the engine is
behaving, I can work on a new gap seal.


- The Matronics Kolb-List Email Forum -
 

Use the List Feature Navigator to browse the many List utilities available such as the Email Subscriptions page, Archive Search & Download, 7-Day Browse, Chat, FAQ, Photoshare, and much more:

http://www.matronics.com/Navigator?Kolb-List
Back to top
Display posts from previous:   
Post new topic   Reply to topic    Matronics Email Lists Forum Index -> Kolb-List All times are GMT - 8 Hours
Page 1 of 1

 
Jump to:  
You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot vote in polls in this forum
You cannot attach files in this forum
You can download files in this forum


Powered by phpBB © 2001, 2005 phpBB Group