Matronics Email Lists Forum Index Matronics Email Lists
Web Forum Interface to the Matronics Email Lists
 
 Get Email Distribution Too!Get Email Distribution Too!    FAQFAQ   SearchSearch   MemberlistMemberlist   UsergroupsUsergroups   RegisterRegister 
 ProfileProfile   Log in to check your private messagesLog in to check your private messages   Log inLog in 

Bleeding Brakes

 
Post new topic   Reply to topic    Matronics Email Lists Forum Index -> Europa-List
View previous topic :: View next topic  
Author Message
eoinmaguire(at)hotmail.co
Guest





PostPosted: Thu Oct 18, 2018 1:07 am    Post subject: Bleeding Brakes Reply with quote

Hi All

Just a question on the correct technique for bleeding the brakes, I received a brake bleed kit from Europa, effectively a syringe and what’s basically a metal screw in funnel.

I’m assuming the funnel bit screws into the top of the cylinder on the finger brake itself but what do i do with the syringe?

Also it recommends dot 5 brake fluid to top up, is there a suitable alternative as dot 5 is proving difficult to get in Ireland?

Kind Regards
Eoin

Sent from my iPhone


- The Matronics Europa-List Email Forum -
 

Use the List Feature Navigator to browse the many List utilities available such as the Email Subscriptions page, Archive Search & Download, 7-Day Browse, Chat, FAQ, Photoshare, and much more:

http://www.matronics.com/Navigator?Europa-List
Back to top
Burrilla



Joined: 25 Apr 2015
Posts: 181

PostPosted: Thu Oct 18, 2018 1:17 am    Post subject: Bleeding Brakes Reply with quote

Your are correct in that the funnel screws into the top of the master cylinder.

I use the syringe to push the fluid up through the bleed screw on the slave cylinder and then through the line into the master. Pushes air out at the same time.

Alan

Sent from my iPad

Quote:
On 18 Oct 2018, at 10:06, Eoin Maguire <eoinmaguire(at)hotmail.com> wrote:



Hi All

Just a question on the correct technique for bleeding the brakes, I received a brake bleed kit from Europa, effectively a syringe and what’s basically a metal screw in funnel.

I’m assuming the funnel bit screws into the top of the cylinder on the finger brake itself but what do i do with the syringe?

Also it recommends dot 5 brake fluid to top up, is there a suitable alternative as dot 5 is proving difficult to get in Ireland?

Kind Regards
Eoin



Sent from my iPhone






- The Matronics Europa-List Email Forum -
 

Use the List Feature Navigator to browse the many List utilities available such as the Email Subscriptions page, Archive Search & Download, 7-Day Browse, Chat, FAQ, Photoshare, and much more:

http://www.matronics.com/Navigator?Europa-List
Back to top
View user's profile Send private message
spcialeffects



Joined: 29 Aug 2012
Posts: 305
Location: Kent

PostPosted: Thu Oct 18, 2018 9:55 am    Post subject: Re: Bleeding Brakes Reply with quote

Alan is correct in what he says. I take it you have a mono? If so let me share my experience with you. I have a mono and bleed the brake pushing fluid up from the bottom. However after 4 or 5 times of doing this the lever was still spongey. The reason for this is that the master cylinder is at an angle so air is still trapped in the front section of the cylinder. In order to remove this air I pushed the fluid up from the bottom until the metal cup you screw in gets half full then PUMP the brake lever until no more bubbles come into the cup and you can just see the fluid being sucked in and out. Then close off the bleed nipple on the caliper and suck some of the fluid in the metal cup up with the syringe.

Regards
Frank Xuereb Kit #165


- The Matronics Europa-List Email Forum -
 

Use the List Feature Navigator to browse the many List utilities available such as the Email Subscriptions page, Archive Search & Download, 7-Day Browse, Chat, FAQ, Photoshare, and much more:

http://www.matronics.com/Navigator?Europa-List
Back to top
View user's profile Send private message
Paul M 383



Joined: 19 Mar 2012
Posts: 97
Location: United Kingdom

PostPosted: Thu Oct 18, 2018 10:16 am    Post subject: Bleeding Brakes Reply with quote

I can't remember where I got these instructions from, but they work fine for the mono:

Brake Bleeding

Funnel; 10 ml syringe; 5 mm allen key; DOT 3 or 4 brake fluid.

1. Remove filler plug & screw the funnel in its place.
2. Pull brake lever smoothly fully aft. Brake fluid should appear in the funnel. Hold the lever aft.
3. Insert the syringe into the funnel and suck out as much fluid as possible. Discard fluid.
4. Nearly fill the syringe with clean fluid and empty into funnel.
5. Release the lever gently, insert the syringe as far as possible and suck out remaining fluid.
6. Remove funnel - the fluid should be just below the uppermost level of the master cylinder.
7. Refit plug. Master cylinder is now bled; if the lever is not firm, brake callipers need bleeding.

HTH

Paul M
383 XS Mono 912S
G-PLPM

--


- The Matronics Europa-List Email Forum -
 

Use the List Feature Navigator to browse the many List utilities available such as the Email Subscriptions page, Archive Search & Download, 7-Day Browse, Chat, FAQ, Photoshare, and much more:

http://www.matronics.com/Navigator?Europa-List
Back to top
View user's profile Send private message Send e-mail AIM Address
Display posts from previous:   
Post new topic   Reply to topic    Matronics Email Lists Forum Index -> Europa-List All times are GMT - 8 Hours
Page 1 of 1

 
Jump to:  
You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot vote in polls in this forum
You cannot attach files in this forum
You can download files in this forum


Powered by phpBB © 2001, 2005 phpBB Group