Matronics Email Lists Forum Index Matronics Email Lists
Web Forum Interface to the Matronics Email Lists
 
 Get Email Distribution Too!Get Email Distribution Too!    FAQFAQ   SearchSearch   MemberlistMemberlist   UsergroupsUsergroups   RegisterRegister 
 ProfileProfile   Log in to check your private messagesLog in to check your private messages   Log inLog in 

Tip up canopy frame

 
Post new topic   Reply to topic    Matronics Email Lists Forum Index -> RV7-List
View previous topic :: View next topic  
Author Message
rv7a.builder(at)yahoo.com
Guest





PostPosted: Mon Jan 01, 2007 8:09 am    Post subject: Tip up canopy frame Reply with quote

Hello Group,

The tip canopy skin C-702 attached to the frame
when lifted interferes with the F-771 skin only in the
area between the hinge line but outside of the hinge
points every part of the C-702 skin moves nicely away
from the F-771. What have builders done to alleviate
this interference so they can open the canopy? I could
notch out a section of the F-771 skin between the
hinge points but that would look almost as hokey as if
the C-702 was shimmed higher than the F-771? Any help
is appreciated. John RV7A.

__________________________________________________


- The Matronics RV7-List Email Forum -
 

Use the List Feature Navigator to browse the many List utilities available such as the Email Subscriptions page, Archive Search & Download, 7-Day Browse, Chat, FAQ, Photoshare, and much more:

http://www.matronics.com/Navigator?RV7-List
Back to top
dan(at)rvproject.com
Guest





PostPosted: Mon Jan 01, 2007 8:39 am    Post subject: Tip up canopy frame Reply with quote

Quote:
from the F-771. What have builders done to alleviate
this interference so they can open the canopy? I could
notch out a section of the F-771 skin between the
hinge points but that would look almost as hokey as if
the C-702 was shimmed higher than the F-771? Any help
is appreciated. John RV7A.

Chop chop, shim shim. You'll have a gap either fore/aft or up/down.

)_( Dan
RV-7 N714D (1165 hours)
www.rvproject.com / www.weathermeister.com


- The Matronics RV7-List Email Forum -
 

Use the List Feature Navigator to browse the many List utilities available such as the Email Subscriptions page, Archive Search & Download, 7-Day Browse, Chat, FAQ, Photoshare, and much more:

http://www.matronics.com/Navigator?RV7-List
Back to top
rv7a.builder(at)yahoo.com
Guest





PostPosted: Tue Jan 02, 2007 10:23 am    Post subject: Tip up canopy frame Reply with quote

Thanks Dan,

I just got an email from Ken (at) Van's and he
indicated that their plane has a .050 gap in that
area. Since the rivet line on the C-702 extends back
aways from the skin edge, does the shim almost have to
extend to the edge to get the lift needed to get the
desired gap? Would a slot cut in either the F-771 or
C-702 be preferable to shimming? Thanks.
--- Dan Checkoway <dan(at)rvproject.com> wrote:

Quote:

<dan(at)rvproject.com>

> from the F-771. What have builders done to
alleviate
> this interference so they can open the canopy? I
could
> notch out a section of the F-771 skin between the
> hinge points but that would look almost as hokey
as if
> the C-702 was shimmed higher than the F-771? Any
help
> is appreciated. John RV7A.

Chop chop, shim shim. You'll have a gap either
fore/aft or up/down.

)_( Dan
RV-7 N714D (1165 hours)
www.rvproject.com / www.weathermeister.com


browse
Subscriptions page,
FAQ,
http://www.matronics.com/Navigator?RV7-List

Web Forums!







__________________________________________________


- The Matronics RV7-List Email Forum -
 

Use the List Feature Navigator to browse the many List utilities available such as the Email Subscriptions page, Archive Search & Download, 7-Day Browse, Chat, FAQ, Photoshare, and much more:

http://www.matronics.com/Navigator?RV7-List
Back to top
dan(at)rvproject.com
Guest





PostPosted: Tue Jan 02, 2007 10:47 am    Post subject: Tip up canopy frame Reply with quote

Quote:
I just got an email from Ken (at) Van's and he
indicated that their plane has a .050 gap in that
area. Since the rivet line on the C-702 extends back
aways from the skin edge, does the shim almost have to
extend to the edge to get the lift needed to get the
desired gap? Would a slot cut in either the F-771 or
C-702 be preferable to shimming? Thanks.

I think you be overthinkin. But whatever works!

)_( Dan


- The Matronics RV7-List Email Forum -
 

Use the List Feature Navigator to browse the many List utilities available such as the Email Subscriptions page, Archive Search & Download, 7-Day Browse, Chat, FAQ, Photoshare, and much more:

http://www.matronics.com/Navigator?RV7-List
Back to top
Display posts from previous:   
Post new topic   Reply to topic    Matronics Email Lists Forum Index -> RV7-List All times are GMT - 8 Hours
Page 1 of 1

 
Jump to:  
You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot vote in polls in this forum
You cannot attach files in this forum
You can download files in this forum


Powered by phpBB © 2001, 2005 phpBB Group