Matronics Email Lists Forum Index Matronics Email Lists
BBS Forum Interface to the Matronics Email Lists
 
 Get Email Distribution Too!Get Email Distribution Too!    FAQFAQ   SearchSearch   MemberlistMemberlist   UsergroupsUsergroups   RegisterRegister 
 ProfileProfile   Log in to check your private messagesLog in to check your private messages   Log inLog in 

Need latest Navworx UAT Console

 
Post new topic   Reply to topic    Matronics Email Lists Forum Index -> RV10-List
View previous topic :: View next topic  
Author Message
Mauledriver(at)nc.rr.com
Guest





PostPosted: Thu Nov 02, 2017 7:04 am    Post subject: Need latest Navworx UAT Console Reply with quote

I have the Navworx unit that will work with the AMOC given a certified
GPS source.  But I don't have a copy of the UAT console that will run,
looking for help.

I tried running the UAT console software I obtained back in 2012 but get
an error on loading, "Nonshared DATA segment required", then if fails to
open.  Anyone have experience with this?

A secondary concern I have is that I recall the UAT console loads a
version of the Navworx software.  If so, this is backlevel for my box
(my box had been sent in since then for a maintenance upgrade).

Does anyone have a copy of the UAT console that they can share or
otherwise advise?  Thanks.

(I'll be posting on the VAF board as well)

Bill "wired up G430w to the deadend box with all appendages crossed" Watson
---
This email has been checked for viruses by Avast antivirus software.
https://www.avast.com/antivirus


- The Matronics RV10-List Email Forum -
 

Use the List Feature Navigator to browse the many List utilities available such as the Email Subscriptions page, Archive Search & Download, 7-Day Browse, Chat, FAQ, Photoshare, and much more:

http://www.matronics.com/Navigator?RV10-List
Back to top
Tim Olson



Joined: 25 Jan 2007
Posts: 2702

PostPosted: Thu Nov 02, 2017 7:14 am    Post subject: Need latest Navworx UAT Console Reply with quote

I have version 4.1.0 if you need. You're right that if you run
the app, it will upgrade your firmware. Mine is far newer
than 2012, but not the 5.0 that Bob talks about.

I have seen one person who couldn't get it to load on their
system, due to an issue with the system, but I was able to load
it on 3 of them.

Tim
On 11/02/2017 10:01 AM, Bill Watson wrote:
Quote:


I have the Navworx unit that will work with the AMOC given a certified
GPS source.  But I don't have a copy of the UAT console that will run,
looking for help.

I tried running the UAT console software I obtained back in 2012 but get
an error on loading, "Nonshared DATA segment required", then if fails to
open.  Anyone have experience with this?

A secondary concern I have is that I recall the UAT console loads a
version of the Navworx software.  If so, this is backlevel for my box
(my box had been sent in since then for a maintenance upgrade).

Does anyone have a copy of the UAT console that they can share or
otherwise advise?  Thanks.

(I'll be posting on the VAF board as well)

Bill "wired up G430w to the deadend box with all appendages crossed" Watson


---
This email has been checked for viruses by Avast antivirus software.
https://www.avast.com/antivirus


- The Matronics RV10-List Email Forum -
 

Use the List Feature Navigator to browse the many List utilities available such as the Email Subscriptions page, Archive Search & Download, 7-Day Browse, Chat, FAQ, Photoshare, and much more:

http://www.matronics.com/Navigator?RV10-List
Back to top
View user's profile Send private message Send e-mail
rleffler



Joined: 05 Nov 2006
Posts: 623

PostPosted: Thu Nov 02, 2017 7:39 am    Post subject: Need latest Navworx UAT Console Reply with quote

If you need 4.1.0 and the manual, let me know.


I haven’t been able to locate anyone that has 5.0 yet.



Get Outlook for iOS


From: owner-rv10-list-server(at)matronics.com <owner-rv10-list-server(at)matronics.com> on behalf of Bill Watson <Mauledriver(at)nc.rr.com>
Sent: Thursday, November 2, 2017 11:01:53 AM
To: rv10-list(at)matronics.com
Subject: Need latest Navworx UAT Console


--> RV10-List message posted by: Bill Watson <Mauledriver(at)nc.rr.com>

I have the Navworx unit that will work with the AMOC given a certified
GPS source. But I don't have a copy of the UAT console that will run,
looking for help.

I tried running the UAT console software I obtained back in 2012 but get
an error on loading, "Nonshared DATA segment required", then if fails to
open. Anyone have experience with this?

A secondary concern I have is that I recall the UAT console loads a
version of the Navworx software. If so, this is backlevel for my box
(my box had been sent in since then for a maintenance upgrade).

Does anyone have a copy of the UAT console that they can share or
otherwise advise? Thanks.

(I'll be posting on the VAF board as well)

Bill "wired up G430w to the deadend box with all appendages crossed" Watson


---
This email has been checked for viruses by Avast antivirus software.
https://www.avast.com/antivirus

===========
Email Forum -
-List">http://www.matronics.com/Navigator?RV10-List
===========
p; - MATRONICS WEB FORUMS -
ums.matronics.com
===========
p; - NEW MATRONICS LIST WIKI -
matronics.com
===========
p; - List Contribution Web Site -
p; -Matt Dralle, List Admin.
http://www.matronics.com/contribution
===========


- The Matronics RV10-List Email Forum -
 

Use the List Feature Navigator to browse the many List utilities available such as the Email Subscriptions page, Archive Search & Download, 7-Day Browse, Chat, FAQ, Photoshare, and much more:

http://www.matronics.com/Navigator?RV10-List

_________________
Bob Leffler
N410BL - Phase I
http://mykitlog.com/rleffler
Back to top
View user's profile Send private message
Mauledriver(at)nc.rr.com
Guest





PostPosted: Thu Nov 02, 2017 8:22 am    Post subject: Need latest Navworx UAT Console Reply with quote

The Mauledriver email is just for posting.

My email is BillisinDurham - gmail  (without the 'is').

I have the current manual from the Dallas folks.

Thanks all!

On 11/2/2017 11:01 AM, Bill Watson wrote:
Quote:


I have the Navworx unit that will work with the AMOC given a certified
GPS source.  But I don't have a copy of the UAT console that will run,
looking for help.

I tried running the UAT console software I obtained back in 2012 but
get an error on loading, "Nonshared DATA segment required", then if
fails to open.  Anyone have experience with this?

A secondary concern I have is that I recall the UAT console loads a
version of the Navworx software.  If so, this is backlevel for my box
(my box had been sent in since then for a maintenance upgrade).

Does anyone have a copy of the UAT console that they can share or
otherwise advise?  Thanks.

(I'll be posting on the VAF board as well)

Bill "wired up G430w to the deadend box with all appendages crossed"
Watson
---
This email has been checked for viruses by Avast antivirus software.
https://www.avast.com/antivirus



- The Matronics RV10-List Email Forum -
 

Use the List Feature Navigator to browse the many List utilities available such as the Email Subscriptions page, Archive Search & Download, 7-Day Browse, Chat, FAQ, Photoshare, and much more:

http://www.matronics.com/Navigator?RV10-List
Back to top
flysrv10(at)gmail.com
Guest





PostPosted: Wed Nov 08, 2017 5:54 am    Post subject: Need latest Navworx UAT Console Reply with quote

Does anyone know if AMCO applies to Avidyne ID-540?
Thanks.
Quote:
On Nov 2, 2017, at 9:38 AM, Bob Leffler <bob(at)thelefflers.com (bob(at)thelefflers.com)> wrote:
If you need 4.1.0 and the manual, let me know.

I haven’t been able to locate anyone that has 5.0 yet.
Get Outlook for iOS
From: owner-rv10-list-server(at)matronics.com (owner-rv10-list-server(at)matronics.com) <owner-rv10-list-server(at)matronics.com (owner-rv10-list-server(at)matronics.com)> on behalf of Bill Watson <Mauledriver(at)nc.rr.com (Mauledriver(at)nc.rr.com)>Sent: Thursday, November 2, 2017 11:01:53 AMTo: rv10-list(at)matronics.com (rv10-list(at)matronics.com)Subject: Need latest Navworx UAT Console
--> RV10-List message posted by: Bill Watson <Mauledriver(at)nc.rr.com (Mauledriver(at)nc.rr.com)>I have the Navworx unit that will work with the AMOC given a certified GPS source. But I don't have a copy of the UAT console that will run, looking for help.I tried running the UAT console software I obtained back in 2012 but get an error on loading, "Nonshared DATA segment required", then if fails to open. Anyone have experience with this?A secondary concern I have is that I recall the UAT console loads a version of the Navworx software. If so, this is backlevel for my box (my box had been sent in since then for a maintenance upgrade).Does anyone have a copy of the UAT console that they can share or otherwise advise? Thanks.(I'll be posting on the VAF board as well)Bill "wired up G430w to the deadend box with all appendages crossed" Watson---This email has been checked for viruses by Avast antivirus software.https://www.avast.com/antivirus===========Email Forum --List">http://www.matronics.com/Navigator?RV10-List===========p; - MATRONICS WEB FORUMS -ums.matronics.com===========p; - NEW MATRONICS LIST WIKI -matronics.com===========p; - List Contribution Web Site -p; -Matt Dralle, List Admin.http://www.matronics.com/contribution===========



- The Matronics RV10-List Email Forum -
 

Use the List Feature Navigator to browse the many List utilities available such as the Email Subscriptions page, Archive Search & Download, 7-Day Browse, Chat, FAQ, Photoshare, and much more:

http://www.matronics.com/Navigator?RV10-List
Back to top
recapen(at)earthlink.net
Guest





PostPosted: Wed Nov 08, 2017 6:32 am    Post subject: Need latest Navworx UAT Console Reply with quote

Rob,

The three AMOCS that have been approved are all for Garmin products.
That having been said, the most recent responses from the FAA indicate that they may be open to approving other data sources that output the "ADS-B OUT+" protocol as it contains the necessary data elements required for position reporting. In my updated AMOC, they specifically reference the ADS-B OUT+ protocol. If the Avidyne outputs it, you should be able to get approval...

I would suggest putting the AMOC together like we did - we can provide you with what we submitted as a sample if you want...

Ralph
--


- The Matronics RV10-List Email Forum -
 

Use the List Feature Navigator to browse the many List utilities available such as the Email Subscriptions page, Archive Search & Download, 7-Day Browse, Chat, FAQ, Photoshare, and much more:

http://www.matronics.com/Navigator?RV10-List
Back to top
flysrv10(at)gmail.com
Guest





PostPosted: Wed Nov 08, 2017 6:57 am    Post subject: Need latest Navworx UAT Console Reply with quote

Ralph, thanks for the quick reply. Please send me the package you provided to the FAA. I spoke to Avidyne and they researching it on their end. I will forward your email (if OK with you) to Avidyne and a copy of my proposal to FAA so they also remain in the loop.

Thanks again
Rob.

Sent from my iPhone

[quote] On Nov 8, 2017, at 7:31 AM, Ralph E. Capen <recapen(at)earthlink.net> wrote:



Rob,

The three AMOCS that have been approved are all for Garmin products.
That having been said, the most recent responses from the FAA indicate that they may be open to approving other data sources that output the "ADS-B OUT+" protocol as it contains the necessary data elements required for position reporting. In my updated AMOC, they specifically reference the ADS-B OUT+ protocol. If the Avidyne outputs it, you should be able to get approval...

I would suggest putting the AMOC together like we did - we can provide you with what we submitted as a sample if you want...

Ralph
--


- The Matronics RV10-List Email Forum -
 

Use the List Feature Navigator to browse the many List utilities available such as the Email Subscriptions page, Archive Search & Download, 7-Day Browse, Chat, FAQ, Photoshare, and much more:

http://www.matronics.com/Navigator?RV10-List
Back to top
rleffler



Joined: 05 Nov 2006
Posts: 623

PostPosted: Wed Nov 08, 2017 7:06 am    Post subject: Need latest Navworx UAT Console Reply with quote

The avidyne does indeed support adsb+


I can assist with writing the AMOC. It will literally take 5-10 minutes to create the doc to send to the FAA


Email me if you want to go down that path.



Get Outlook for iOS


From: owner-rv10-list-server(at)matronics.com <owner-rv10-list-server(at)matronics.com> on behalf of Ralph E. Capen <recapen(at)earthlink.net>
Sent: Wednesday, November 8, 2017 9:31:07 AM
To: rv10-list(at)matronics.com
Subject: Re: Need latest Navworx UAT Console


--> RV10-List message posted by: "Ralph E. Capen" <recapen(at)earthlink.net>

Rob,

The three AMOCS that have been approved are all for Garmin products.
That having been said, the most recent responses from the FAA indicate that they may be open to approving other data sources that output the "ADS-B OUT+" protocol as it contains the necessary data elements required for position reporting. In my updated AMOC, they specifically reference the ADS-B OUT+ protocol. If the Avidyne outputs it, you should be able to get approval...

I would suggest putting the AMOC together like we did - we can provide you with what we submitted as a sample if you want...

Ralph
--


- The Matronics RV10-List Email Forum -
 

Use the List Feature Navigator to browse the many List utilities available such as the Email Subscriptions page, Archive Search & Download, 7-Day Browse, Chat, FAQ, Photoshare, and much more:

http://www.matronics.com/Navigator?RV10-List

_________________
Bob Leffler
N410BL - Phase I
http://mykitlog.com/rleffler
Back to top
View user's profile Send private message
flysrv10(at)gmail.com
Guest





PostPosted: Wed Nov 08, 2017 8:04 am    Post subject: Need latest Navworx UAT Console Reply with quote

Thanks Bob. Yes ...please, please. What do you need from me?

Sent from my iPhone

On Nov 8, 2017, at 8:05 AM, Bob Leffler <bob(at)thelefflers.com (bob(at)thelefflers.com)> wrote:
[quote] The avidyne does indeed support adsb+


I can assist with writing the AMOC. It will literally take 5-10 minutes to create the doc to send to the FAA


Email me if you want to go down that path.



Get Outlook for iOS


From: owner-rv10-list-server(at)matronics.com (owner-rv10-list-server(at)matronics.com) <owner-rv10-list-server(at)matronics.com (owner-rv10-list-server(at)matronics.com)> on behalf of Ralph E. Capen <recapen(at)earthlink.net (recapen(at)earthlink.net)>
Sent: Wednesday, November 8, 2017 9:31:07 AM
To: rv10-list(at)matronics.com (rv10-list(at)matronics.com)
Subject: Re: Need latest Navworx UAT Console


--> RV10-List message posted by: "Ralph E. Capen" <recapen(at)earthlink.net (recapen(at)earthlink.net)>

Rob,

The three AMOCS that have been approved are all for Garmin products.
That having been said, the most recent responses from the FAA indicate that they may be open to approving other data sources that output the "ADS-B OUT+" protocol as it contains the necessary data elements required for position reporting. In my updated AMOC, they specifically reference the ADS-B OUT+ protocol. If the Avidyne outputs it, you should be able to get approval...

I would suggest putting the AMOC together like we did - we can provide you with what we submitted as a sample if you want...

Ralph
--


- The Matronics RV10-List Email Forum -
 

Use the List Feature Navigator to browse the many List utilities available such as the Email Subscriptions page, Archive Search & Download, 7-Day Browse, Chat, FAQ, Photoshare, and much more:

http://www.matronics.com/Navigator?RV10-List
Back to top
rleffler



Joined: 05 Nov 2006
Posts: 623

PostPosted: Wed Nov 08, 2017 1:54 pm    Post subject: Need latest Navworx UAT Console Reply with quote

Wire the Avidyne to the ads600-b using the adsb+ protocol.


I dont recall if there is an Avidyne example in the Navworx manual.


Use the gtn650/gns430w as an example. The gps pins will be different, but the NavWorxs side will be the same.


Disconnect the internal gps antenna


Change the Navworx configuration to use the external gps


Validate that you have three green status indicators


Fly and get a copy of the public performance report from the FAA.


If there is an Avidyne schematic in the Navworx manual, we can cut and paste that, if not youll have to create an installation schematic. Again, use the Garmin schematics as an example.


Then let me know. Its a simple cut and paste job using my application as a template.



Get Outlook for iOS


From: owner-rv10-list-server(at)matronics.com <owner-rv10-list-server(at)matronics.com> on behalf of Rob Kermanj <flysrv10(at)gmail.com>
Sent: Wednesday, November 8, 2017 11:02:27 AM
To: rv10-list(at)matronics.com
Subject: Re: Need latest Navworx UAT Console

Thanks Bob. Yes ...please, please. What do you need from me?

Sent from my iPhone

On Nov 8, 2017, at 8:05 AM, Bob Leffler <bob(at)thelefflers.com (bob(at)thelefflers.com)> wrote:


[quote] The avidyne does indeed support adsb+


I can assist with writing the AMOC. It will literally take 5-10 minutes to create the doc to send to the FAA


Email me if you want to go down that path.



Get Outlook for iOS


From: owner-rv10-list-server(at)matronics.com (owner-rv10-list-server(at)matronics.com) <owner-rv10-list-server(at)matronics.com (owner-rv10-list-server(at)matronics.com)> on behalf of Ralph E. Capen <recapen(at)earthlink.net (recapen(at)earthlink.net)>
Sent: Wednesday, November 8, 2017 9:31:07 AM
To: rv10-list(at)matronics.com (rv10-list(at)matronics.com)
Subject: Re: Need latest Navworx UAT Console


--> RV10-List message posted by: "Ralph E. Capen" <recapen(at)earthlink.net (recapen(at)earthlink.net)>

Rob,

The three AMOCS that have been approved are all for Garmin products.
That having been said, the most recent responses from the FAA indicate that they may be open to approving other data sources that output the "ADS-B OUT+" protocol as it contains the necessary data elements required for position reporting. In my updated AMOC, they specifically reference the ADS-B OUT+ protocol. If the Avidyne outputs it, you should be able to get approval...

I would suggest putting the AMOC together like we did - we can provide you with what we submitted as a sample if you want...

Ralph
--


- The Matronics RV10-List Email Forum -
 

Use the List Feature Navigator to browse the many List utilities available such as the Email Subscriptions page, Archive Search & Download, 7-Day Browse, Chat, FAQ, Photoshare, and much more:

http://www.matronics.com/Navigator?RV10-List

_________________
Bob Leffler
N410BL - Phase I
http://mykitlog.com/rleffler
Back to top
View user's profile Send private message
flysrv10(at)gmail.com
Guest





PostPosted: Wed Nov 08, 2017 3:54 pm    Post subject: Need latest Navworx UAT Console Reply with quote

Thanks Bob. Will do. Will let you how it turns out.

Sent from my iPhone

[quote] On Nov 8, 2017, at 2:52 PM, Bob Leffler <bob(at)thelefflers.com> wrote:

Wire the Avidyne to the ads600-b using the adsb+ protocol.

I don’t recall if there is an Avidyne example in the Navworx manual.

Use the gtn650/gns430w as an example. The gps pins will be different, but the NavWorxs side will be the same.

Disconnect the internal gps antenna

Change the Navworx configuration to use the external gps

Validate that you have three green status indicators

Fly and get a copy of the public performance report from the FAA.

If there is an Avidyne schematic in the Navworx manual, we can cut and paste that, if not you’ll have to create an installation schematic. Again, use the Garmin schematics as an example.

Then let me know. It’s a simple cut and paste job using my application as a template.

Get Outlook for iOS
From: owner-rv10-list-server(at)matronics.com <owner-rv10-list-server(at)matronics.com> on behalf of Rob Kermanj <flysrv10(at)gmail.com>
Sent: Wednesday, November 8, 2017 11:02:27 AM
To: rv10-list(at)matronics.com
Subject: Re: Need latest Navworx UAT Console

Thanks Bob. Yes ...please, please. What do you need from me?

Sent from my iPhone

On Nov 8, 2017, at 8:05 AM, Bob Leffler <bob(at)thelefflers.com> wrote:

> The avidyne does indeed support adsb+
>
> I can assist with writing the AMOC. It will literally take 5-10 minutes to create the doc to send to the FAA
>
> Email me if you want to go down that path.
>
> Get Outlook for iOS
> From: owner-rv10-list-server(at)matronics.com <owner-rv10-list-server(at)matronics.com> on behalf of Ralph E. Capen <recapen(at)earthlink.net>
> Sent: Wednesday, November 8, 2017 9:31:07 AM
> To: rv10-list(at)matronics.com
> Subject: Re: Need latest Navworx UAT Console
>
>
>
> Rob,
>
> The three AMOCS that have been approved are all for Garmin products.
> That having been said, the most recent responses from the FAA indicate that they may be open to approving other data sources that output the "ADS-B OUT+" protocol as it contains the necessary data elements required for position reporting. In my updated AMOC, they specifically reference the ADS-B OUT+ protocol. If the Avidyne outputs it, you should be able to get approval..


- The Matronics RV10-List Email Forum -
 

Use the List Feature Navigator to browse the many List utilities available such as the Email Subscriptions page, Archive Search & Download, 7-Day Browse, Chat, FAQ, Photoshare, and much more:

http://www.matronics.com/Navigator?RV10-List
Back to top
Display posts from previous:   
Post new topic   Reply to topic    Matronics Email Lists Forum Index -> RV10-List All times are GMT - 8 Hours
Page 1 of 1

 
Jump to:  
You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot vote in polls in this forum
You cannot attach files in this forum
You can download files in this forum


Powered by phpBB © 2001, 2005 phpBB Group