|
Matronics Email Lists Web Forum Interface to the Matronics Email Lists
|
View previous topic :: View next topic |
Author |
Message |
Deems Davis
Joined: 09 Jan 2006 Posts: 925
|
Posted: Wed Mar 01, 2006 4:54 pm Post subject: I'm stumped |
|
|
I'm stumped (not a rare instance). I'm attaching the WD-1004 Nose Gear
Tension Fittings to the F-1048 Fwd Fusalage Ribs prior to riveting the
assemblies to the Firewall (Plans Sec 27-4 step 7). There are 50 AN470
AD 4-5 rivets that get set in this section . There are ALSO 8 AN470 AD
4-6 rivets that are the most forward (closest to the firewall) I can't
seem to figure a way to get a rivet gun on these 8 rivets, unless I move
the shop head to the other (inside) side of the rib. Anybody got have a
tip here?
Deems Davis # 406
Fuse
http://deemsrv10.com
| - The Matronics RV10-List Email Forum - | | Use the List Feature Navigator to browse the many List utilities available such as the Email Subscriptions page, Archive Search & Download, 7-Day Browse, Chat, FAQ, Photoshare, and much more:
http://www.matronics.com/Navigator?RV10-List |
|
|
|
Back to top |
|
|
Rick S.
Joined: 12 Feb 2006 Posts: 347 Location: Las Vegas
|
Posted: Wed Mar 01, 2006 6:28 pm Post subject: I'm stumped |
|
|
Deems,
You will have to trim the firewall stiffeners. Go up about 1" and over a 1/2" shaped like a 30/60 triangle, and trim it enough to get your offset rivet set on the head...it's a pain. I'll do a picture and email to you in a bit...dinner time.
Rick S.
40185
Finishing kit inventory
| - The Matronics RV10-List Email Forum - | | Use the List Feature Navigator to browse the many List utilities available such as the Email Subscriptions page, Archive Search & Download, 7-Day Browse, Chat, FAQ, Photoshare, and much more:
http://www.matronics.com/Navigator?RV10-List |
|
_________________ Rick S.
RV-10
40185 |
|
Back to top |
|
|
wcurtis(at)core.com Guest
|
Posted: Thu Mar 02, 2006 9:00 am Post subject: I'm stumped |
|
|
[quote]You will have to trim the firewall stiffeners. Go up about 1" >and over a 1/2" shaped like a 30/60 triangle, and trim it enough >to get your offset rivet set on the head...it's a pain. Whoa there! Before you go trimming firewall stiffeners, check on page 27-4, Step 7. Van’s recommends you place the shop heads on the outboard side of the WD-1004 fitting. This recommended direction does not provide for the most finish look, but I always try to place the manufacturer’s head on the thinner material. In this case it is the F-1048-L/R. Van’s rarely specifies the direction of the rivet head but in this case they did. If you look at my page at the below link, I did a compromise. I followed the recommendation except the top three rows of rivets. http://wcurtis.nerv10.com/08fuselage/fuselage03f.html William Curtis http://nerv10.com/
| - The Matronics RV10-List Email Forum - | | Use the List Feature Navigator to browse the many List utilities available such as the Email Subscriptions page, Archive Search & Download, 7-Day Browse, Chat, FAQ, Photoshare, and much more:
http://www.matronics.com/Navigator?RV10-List |
|
|
|
Back to top |
|
|
Rick S.
Joined: 12 Feb 2006 Posts: 347 Location: Las Vegas
|
Posted: Thu Mar 02, 2006 10:04 am Post subject: I'm stumped |
|
|
William,
Sorry I may have been thinking about a different section, the area I was talking about is in the photo, it is the most forward rivet in the 1002/1003 brackets. I may have jumped the gun, the are your photos show I followed the plans regarding rivet direction and had no issues.
Rick S.
40185
| - The Matronics RV10-List Email Forum - | | Use the List Feature Navigator to browse the many List utilities available such as the Email Subscriptions page, Archive Search & Download, 7-Day Browse, Chat, FAQ, Photoshare, and much more:
http://www.matronics.com/Navigator?RV10-List |
|
Description: |
|
Filesize: |
370.44 KB |
Viewed: |
331 Time(s) |
|
_________________ Rick S.
RV-10
40185 |
|
Back to top |
|
|
Rick S.
Joined: 12 Feb 2006 Posts: 347 Location: Las Vegas
|
Posted: Thu Mar 02, 2006 10:10 am Post subject: I'm stumped |
|
|
Deems,
Sorry I was thinking of a different area, William posted the correct respons to double check your rivet direction. My mind is still bouncing after riveting the 1002/1003 to the lower forward longerons. That is where I was refering to regarding the trimming of the stiffener. See later post for what I was thinking.
Rick S.
40185
| - The Matronics RV10-List Email Forum - | | Use the List Feature Navigator to browse the many List utilities available such as the Email Subscriptions page, Archive Search & Download, 7-Day Browse, Chat, FAQ, Photoshare, and much more:
http://www.matronics.com/Navigator?RV10-List |
|
_________________ Rick S.
RV-10
40185 |
|
Back to top |
|
|
Deems Davis
Joined: 09 Jan 2006 Posts: 925
|
Posted: Thu Mar 02, 2006 1:00 pm Post subject: I'm stumped |
|
|
Thanks for the responses, now, if i could only learn to read............
Deems Davis # 406
Fuse
http://deemsrv10.com/
Rick wrote:
Quote: |
Deems,
Sorry I was thinking of a different area, William posted the correct respons to double check your rivet direction. My mind is still bouncing after riveting the 1002/1003 to the lower forward longerons. That is where I was refering to regarding the trimming of the stiffener. See later post for what I was thinking.
Rick S.
40185
|
| - The Matronics RV10-List Email Forum - | | Use the List Feature Navigator to browse the many List utilities available such as the Email Subscriptions page, Archive Search & Download, 7-Day Browse, Chat, FAQ, Photoshare, and much more:
http://www.matronics.com/Navigator?RV10-List |
|
|
|
Back to top |
|
|
|
|
You cannot post new topics in this forum You cannot reply to topics in this forum You cannot edit your posts in this forum You cannot delete your posts in this forum You cannot vote in polls in this forum You cannot attach files in this forum You can download files in this forum
|
Powered by phpBB © 2001, 2005 phpBB Group
|