Matronics Email Lists Forum Index Matronics Email Lists
Web Forum Interface to the Matronics Email Lists
 
 Get Email Distribution Too!Get Email Distribution Too!    FAQFAQ   SearchSearch   MemberlistMemberlist   UsergroupsUsergroups   RegisterRegister 
 ProfileProfile   Log in to check your private messagesLog in to check your private messages   Log inLog in 

control crossover

 
Post new topic   Reply to topic    Matronics Email Lists Forum Index -> KIS-List
View previous topic :: View next topic  
Author Message
bakerocb



Joined: 15 Jan 2006
Posts: 727
Location: FAIRFAX VA

PostPosted: Wed Aug 11, 2010 4:34 am    Post subject: control crossover Reply with quote

8/11/2010

Hello Rich, Thanks for your quick and detailed response. You wrote:

1) "What is the requirement OC?"

I suppose that the contol stop requirement on an EAB (Experimental Amateur
Built) airplane is whatever the kit provider or the aircraft builder decides
it to
be. If we look to 14 CFR Part 23 for type certificated airplanes for
guidance here is what we find:

"23.675 Stops.

(a) Each control system must have stops that positively limit the range of
motion of each movable aerodynamic surface controlled by the system.

(b) Each stop must be located so that wear, slackness, or takeup adjustments
will not adversely affect the control characteristics of the airplane
because of a change in the range of surface travel.

(c) Each stop must be able to withstand any loads corresponding to the
design conditions for the control system."
2) "Now that I think about it, it seems to me that the control stops should
be put as close to the flight controls as possible since there is always
play in the system."
Sub paragraph (b) above certainly supports the idea of putting the stops
close to the actual control surface location.

3) "The crontrol stop was emitted off the new one and the ¨C¨ was modified
to act as the control stop by allowing the stick to hit the edge."

You can see in the attached photo number 0371 that I used the control stick
hitting the edge of an adjustable U clamped aluminum bar as an aileron
control stop -- one was required for each stick to provide for a stop in
both directions.

4) "Rudder, Uhhhhhhhh forgot."

It turned out that the rudder stops were the more difficult to come up with.
I can't remember what I had initially, but it turned out to be inadequate
since I managed to create a dent in my rudder surface by jamming the rudder
into the inner end of the elevator while trying to taxi the airplane with
the original inadequate Matco brakes.

The boat cable clamps** that I eventually came up with did not crimp the
rudder cables and the ty wrapped aluminum angles butting up against the seat
back have proved to be effective if a bit clunky in appearance.

I had modified my rudder control system to have an internal bellcrank
mounted in the aft fuselage bottom with a push rod going back to the rudder
itself. This eliminated the rudder cable coming out of the fuselage side on
its way back to the rudder horn. Unfortunately I did not think to
incorporate an adjustable rudder stop in my design of the internal
bellcrank.

Thanks again for your continuing support of the KIS community -- it is much
appreciated.

'OC' Baker Says: "The best investment we can make is the time and effort to
gather and understand knowledge."

**PS: http://www.perko.com/ Rope clamp part number 1226

================================================
---


- The Matronics KIS-List Email Forum -
 

Use the List Feature Navigator to browse the many List utilities available such as the Email Subscriptions page, Archive Search & Download, 7-Day Browse, Chat, FAQ, Photoshare, and much more:

http://www.matronics.com/Navigator?KIS-List



100_0371.jpg
 Description:
 Filesize:  293.39 KB
 Viewed:  1992 Time(s)

100_0371.jpg


Back to top
View user's profile Send private message
Display posts from previous:   
Post new topic   Reply to topic    Matronics Email Lists Forum Index -> KIS-List All times are GMT - 8 Hours
Page 1 of 1

 
Jump to:  
You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot vote in polls in this forum
You cannot attach files in this forum
You can download files in this forum


Powered by phpBB © 2001, 2005 phpBB Group