Matronics Email Lists Forum Index Matronics Email Lists
Web Forum Interface to the Matronics Email Lists
 
 Get Email Distribution Too!Get Email Distribution Too!    FAQFAQ   SearchSearch   MemberlistMemberlist   UsergroupsUsergroups   RegisterRegister 
 ProfileProfile   Log in to check your private messagesLog in to check your private messages   Log inLog in 

Fuel pump cooling

 
Post new topic   Reply to topic    Matronics Email Lists Forum Index -> LycomingEngines-List
View previous topic :: View next topic  
Author Message
recapen(at)earthlink.net
Guest





PostPosted: Tue Sep 11, 2012 3:27 am    Post subject: Fuel pump cooling Reply with quote

For those of you that have installed a cooling shroud on your fuel pump, are you using the entire inch diameter for the flange hole to steal the air? Is it enough / too much?

I'm thinking I might open it the full inch and put inserts to reduce it...but then how do I know what's enough.....

Ralph


- The Matronics LycomingEngines-List Email Forum -
 

Use the List Feature Navigator to browse the many List utilities available such as the Email Subscriptions page, Archive Search & Download, 7-Day Browse, Chat, FAQ, Photoshare, and much more:

http://www.matronics.com/Navigator?LycomingEngines-List
Back to top
BARRY CHECK 6



Joined: 15 Mar 2011
Posts: 738

PostPosted: Tue Sep 11, 2012 5:24 am    Post subject: Fuel pump cooling Reply with quote

Ralph:

The 1" size is perfectly acceptable.  You can always make it smaller... But, you can't make it bigger - BUT, don't forget, the exhaust area has to be at least  TWICE the AREA of the input.  Area of a circle = 2Pi*R^2.


Barry
 

On Tue, Sep 11, 2012 at 7:27 AM, Ralph E. Capen <recapen(at)earthlink.net (recapen(at)earthlink.net)> wrote:
[quote]--> LycomingEngines-List message posted by: "Ralph E. Capen" <recapen(at)earthlink.net (recapen(at)earthlink.net)>

For those of you that have installed a cooling shroud on your fuel pump, are you using the entire inch diameter for the flange hole to steal the air?  Is it enough / too much?

I'm thinking I might open it the full inch and put inserts to reduce it..but then how do I know what's enough.....

Ralph



===========
nes-List" target="_blank">http://www.matronics.com/Navigator?LycomingEngines-List
===========
http://forums.matronics.com
===========
le, List Admin.
="_blank">http://www.matronics.com/contribution
===========



[b]


- The Matronics LycomingEngines-List Email Forum -
 

Use the List Feature Navigator to browse the many List utilities available such as the Email Subscriptions page, Archive Search & Download, 7-Day Browse, Chat, FAQ, Photoshare, and much more:

http://www.matronics.com/Navigator?LycomingEngines-List
Back to top
View user's profile Send private message Send e-mail
recapen(at)earthlink.net
Guest





PostPosted: Tue Sep 11, 2012 5:56 am    Post subject: Fuel pump cooling Reply with quote

Thanks Barry,

It always comes back to high-school math......

I'm thinking that since this has some official sticker on it, the inlet/outlet areas have been optimized as you have described.

Making the inlet smaller will provide continued conformance to the criteria you have listed.

Ralph

--


- The Matronics LycomingEngines-List Email Forum -
 

Use the List Feature Navigator to browse the many List utilities available such as the Email Subscriptions page, Archive Search & Download, 7-Day Browse, Chat, FAQ, Photoshare, and much more:

http://www.matronics.com/Navigator?LycomingEngines-List
Back to top
BARRY CHECK 6



Joined: 15 Mar 2011
Posts: 738

PostPosted: Tue Sep 11, 2012 7:09 am    Post subject: Fuel pump cooling Reply with quote

Ralph:

Do not become too concerned about vapor lock.  Yes, some of the stories you hear are true, but many more are exaggerated.  The best things you can do towards its prevention are:
1 - Point the plane into the wind after shutdown.
2 - Open all cowl flaps (if any)
3 - Open the oil door
4 - Turn on and take off with boost pump ON.
5 - Leave boost pump ON until you reach a safe altitude.
6 - The rest is all dependent upon your building practices - The routing of fuel lines and Fire Sleeves, as mentioned.


I would NOT reduce the size of the SCAT tube any smaller than 1".  Volume of air flow is NOT only dependent upon size of the tube but also the Flow Dynamics of the tube.  This means internal turbulence and restrictions [bends, obstructions, roughness, corrugation and input & output restrictions].  And, if you really want to explore the dynamics of this - Look up Open and Closed end Resonance.  I know, I know, way more information than needed Wink


Barry   


On Tue, Sep 11, 2012 at 9:53 AM, Ralph E. Capen <recapen(at)earthlink.net (recapen(at)earthlink.net)> wrote:
[quote]--> LycomingEngines-List message posted by: "Ralph E. Capen" <recapen(at)earthlink.net (recapen(at)earthlink.net)>


Thanks Barry,

It always comes back to high-school math......

I'm thinking that since this has some official sticker on it, the inlet/outlet areas have been optimized as you have described.

Making the inlet smaller will provide continued conformance to the criteria you have listed.

Ralph



--


- The Matronics LycomingEngines-List Email Forum -
 

Use the List Feature Navigator to browse the many List utilities available such as the Email Subscriptions page, Archive Search & Download, 7-Day Browse, Chat, FAQ, Photoshare, and much more:

http://www.matronics.com/Navigator?LycomingEngines-List
Back to top
View user's profile Send private message Send e-mail
Display posts from previous:   
Post new topic   Reply to topic    Matronics Email Lists Forum Index -> LycomingEngines-List All times are GMT - 8 Hours
Page 1 of 1

 
Jump to:  
You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot vote in polls in this forum
You cannot attach files in this forum
You can download files in this forum


Powered by phpBB © 2001, 2005 phpBB Group