 |
Matronics Email Lists
Web Forum Interface to the Matronics Email Lists
|
| View previous topic :: View next topic |
| Author |
Message |
PMorel
Joined: 09 Jul 2007
Posts: 62
Location: Locust Grove, GA USA
|
 Posted: Sat Nov 12, 2011 5:39 am Post subject: Classic IV Firewall |
 |
|
I'm building a Classic IV and was hoping someone has the dimensions of the lower firewall panels. I'll be installing a Rotax 912 and I have the cutout for the starter for the panel. I only need the dimensions for the center and ether left or right panel since I assume they are the same size. Thanks
Paul
[quote][b]
| | - The Matronics Kitfox-List Email Forum - | | | Use the List Feature Navigator to browse the many List utilities available such as the Email Subscriptions page, Archive Search & Download, 7-Day Browse, Chat, FAQ, Photoshare, and much more:
http://www.matronics.com/Navigator?Kitfox-List |
|
_________________
Paul Morel
912 Speedster
Locust Grove, GA
www.WingsAirPhotos.com |
|
| Back to top |
|
 |
lcfitt(at)sbcglobal.net
Guest
|
| Posted: Sat Nov 12, 2011 8:19 am Post subject: Classic IV Firewall |
|
|
Paul,
The dimensions of what I would call the foot wells are : top forward bend begins right below the side engine mount and is 4" to the downward bend. The lower section runs from that bend 10-3/8" to the bottom bend. This results is a foot well that extends forward of the plane of the firewall slightly under 4" at the top, tapering to zero at the bottom. The extension that fits over and around the bottom front of the fuselage is 1-3/8" top to bend and then extends aft under the fuselage 5-3/8". The gap between the foot wells is 6" wide.
If this sounds confusing, drop another note.
Lowell
From: PMorel (pmorel(at)bellsouth.net)
Sent: Saturday, November 12, 2011 5:36 AM
To: kitfox-list(at)matronics.com (kitfox-list(at)matronics.com)
Subject: Classic IV Firewall
I'm building a Classic IV and was hoping someone has the dimensions of the lower firewall panels. I'll be installing a Rotax 912 and I have the cutout for the starter for the panel. I only need the dimensions for the center and ether left or right panel since I assume they are the same size. Thanks
Paul
[quote]
href="http://www.aeroelectric.com">www.aeroelectric.com
href="http://www.buildersbooks.com">www.buildersbooks.com
href="http://www.homebuilthelp.com">www.homebuilthelp.com
href="http://www.matronics.com/contribution">http://www.matronics.com/chref="http://www.matronics.com/Navigator?Kitfox-List">http://www.matronhref="http://forums.matronics.com">http://forums.matronics.com
href="http://www.matronics.com/contribution">http://www.matronics.com/c
[b]
| | - The Matronics Kitfox-List Email Forum - | | | Use the List Feature Navigator to browse the many List utilities available such as the Email Subscriptions page, Archive Search & Download, 7-Day Browse, Chat, FAQ, Photoshare, and much more:
http://www.matronics.com/Navigator?Kitfox-List |
|
|
|
| Back to top |
|
|
|
|
You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot vote in polls in this forum
You cannot attach files in this forum
You can download files in this forum
|
Powered by phpBB © 2001, 2005 phpBB Group
|
Get Email Distribution Too!
FAQ
Search
Memberlist
Usergroups
Register
Profile
Log in to check your private messages
Log in
