Matronics Email Lists Forum Index Matronics Email Lists
Web Forum Interface to the Matronics Email Lists
 
 Get Email Distribution Too!Get Email Distribution Too!    FAQFAQ   SearchSearch   MemberlistMemberlist   UsergroupsUsergroups   RegisterRegister 
 ProfileProfile   Log in to check your private messagesLog in to check your private messages   Log inLog in 

Terminal ID?

 
Post new topic   Reply to topic    Matronics Email Lists Forum Index -> AeroElectric-List
View previous topic :: View next topic  
Author Message
donjohnston



Joined: 13 Dec 2009
Posts: 231

PostPosted: Sun Sep 08, 2013 5:49 am    Post subject: Terminal ID? Reply with quote

I'm hooking up the the CHT/EGT probes to my Grand Rapids EIS. I had a couple bad crimps on the male spade connectors but I didn't have enough spares. GR sent me some extras but they changed to a different style and those don't work in my AMP 47386-R crimping tool.

I've poked around on Mouser, but all I can find are ring and butt splice. No luck on tabs.

Any suggestions on a PN?


- The Matronics AeroElectric-List Email Forum -
 

Use the List Feature Navigator to browse the many List utilities available such as the Email Subscriptions page, Archive Search & Download, 7-Day Browse, Chat, FAQ, Photoshare, and much more:

http://www.matronics.com/Navigator?AeroElectric-List



569a.jpg
 Description:
 Filesize:  158.87 KB
 Viewed:  1664 Time(s)

569a.jpg


Back to top
View user's profile Send private message
Kellym



Joined: 10 Jan 2006
Posts: 1700
Location: Sun Lakes AZ

PostPosted: Sun Sep 08, 2013 7:16 am    Post subject: Terminal ID? Reply with quote

Probes do seem to have varying connectors. Those for EI probes have a
bit of a bump in the middle but both male and female are fast-on fully
insulated.
On Dynon the insulation is rounder, and the male spades do not have
insulation over the spade, just the crimp area. I have had some luck
matching up what I needed for extras at either Radio Shack or Home
Depot, just being careful to only select ones with translucent nylon
insulation, not opaque vinyl.
Haven't run into ones that don't use same crimp as any other ring or
fast-on terminal. Seems odd that they would supply a connector that
doesn't use a standard crimp.

On 9/8/2013 6:49 AM, donjohnston wrote:
Quote:


I'm hooking up the the CHT/EGT probes to my Grand Rapids EIS. I had a couple bad crimps on the male spade connectors but I didn't have enough spares. GR sent me some extras but they changed to a different style and those don't work in my AMP 47386-R crimping tool.

I've poked around on Mouser, but all I can find are ring and butt splice. No luck on tabs.

Any suggestions on a PN?


Read this topic online here:

http://forums.matronics.com/viewtopic.php?p=408229#408229


Attachments:

http://forums.matronics.com//files/569a_158.jpg



- The Matronics AeroElectric-List Email Forum -
 

Use the List Feature Navigator to browse the many List utilities available such as the Email Subscriptions page, Archive Search & Download, 7-Day Browse, Chat, FAQ, Photoshare, and much more:

http://www.matronics.com/Navigator?AeroElectric-List

_________________
Kelly McMullen
A&P/IA, EAA Tech Counselor # 5286
KCHD
Back to top
View user's profile Send private message
Display posts from previous:   
Post new topic   Reply to topic    Matronics Email Lists Forum Index -> AeroElectric-List All times are GMT - 8 Hours
Page 1 of 1

 
Jump to:  
You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot vote in polls in this forum
You cannot attach files in this forum
You can download files in this forum


Powered by phpBB © 2001, 2005 phpBB Group