|
Matronics Email Lists Web Forum Interface to the Matronics Email Lists
|
View previous topic :: View next topic |
Author |
Message |
paul(at)eckenroth.com Guest
|
Posted: Sun Apr 07, 2019 11:18 am Post subject: Battery Contactor Voltage Drop |
|
|
What is the typical voltage drop across the poles of a healthy battery contactor. Is there a failure or aging mode where the voltage drop increases. How about typical voltage drop across the diode bridge rectifier for the essential buss. After eleven trouble free years I need to sort out some problems with my RV9A. Thanks for any information.
Paul
| - The Matronics AeroElectric-List Email Forum - | | Use the List Feature Navigator to browse the many List utilities available such as the Email Subscriptions page, Archive Search & Download, 7-Day Browse, Chat, FAQ, Photoshare, and much more:
http://www.matronics.com/Navigator?AeroElectric-List |
|
|
|
Back to top |
|
|
ceengland7(at)gmail.com Guest
|
Posted: Sun Apr 07, 2019 1:31 pm Post subject: Battery Contactor Voltage Drop |
|
|
On 4/7/2019 2:16 PM, Paul Eckenroth wrote:
Quote: | What is the typical voltage drop across the poles of a healthy battery
contactor. Is there a failure or aging mode where the voltage drop
increases. How about typical voltage drop across the diode bridge
rectifier for the essential buss. After eleven trouble free years I
need to sort out some problems with my RV9A. Thanks for any information.
Paul
Drop across a good contactor should be hard to measure reliably with a
|
regular voltmeter.
Drop across a typical silicon diode will be zero with no load, but will
be around 0.7V at any significant load.
If you have a Schottky diode (not likely, but possible), it will be
around 0.5V or less under load.
---
This email has been checked for viruses by Avast antivirus software.
https://www.avast.com/antivirus
| - The Matronics AeroElectric-List Email Forum - | | Use the List Feature Navigator to browse the many List utilities available such as the Email Subscriptions page, Archive Search & Download, 7-Day Browse, Chat, FAQ, Photoshare, and much more:
http://www.matronics.com/Navigator?AeroElectric-List |
|
|
|
Back to top |
|
|
N509RV(at)eckenroth.com Guest
|
Posted: Mon Apr 08, 2019 7:33 am Post subject: Battery Contactor Voltage Drop |
|
|
Thanks for the information Charlie. The reason for the question is that I have 1 EFIS each on the regular buss and the E buss which show .9V difference. Does the diode degrade in a way that would increase voltage drop.
Paul
On Sun, Apr 7, 2019 at 5:34 PM Charlie England <ceengland7(at)gmail.com (ceengland7(at)gmail.com)> wrote:
Quote: | --> AeroElectric-List message posted by: Charlie England <ceengland7(at)gmail.com (ceengland7(at)gmail.com)>
On 4/7/2019 2:16 PM, Paul Eckenroth wrote:
> What is the typical voltage drop across the poles of a healthy battery
> contactor. Is there a failure or aging mode where the voltage drop
> increases. How about typical voltage drop across the diode bridge
> rectifier for the essential buss. After eleven trouble free years I
> need to sort out some problems with my RV9A. Thanks for any information.
>
> Paul
Drop across a good contactor should be hard to measure reliably with a
regular voltmeter.
Drop across a typical silicon diode will be zero with no load, but will
be around 0.7V at any significant load.
If you have a Schottky diode (not likely, but possible), it will be
around 0.5V or less under load.
---
This email has been checked for viruses by Avast antivirus software.
https://www.avast.com/antivirus
===========
-
Electric-List" rel="noreferrer" target="_blank">http://www.matronics.com/Navigator?AeroElectric-List
===========
FORUMS -
eferrer" target="_blank">http://forums.matronics.com
===========
WIKI -
errer" target="_blank">http://wiki.matronics.com
===========
b Site -
-Matt Dralle, List Admin.
rel="noreferrer" target="_blank">http://www.matronics.com/contribution
===========
|
| - The Matronics AeroElectric-List Email Forum - | | Use the List Feature Navigator to browse the many List utilities available such as the Email Subscriptions page, Archive Search & Download, 7-Day Browse, Chat, FAQ, Photoshare, and much more:
http://www.matronics.com/Navigator?AeroElectric-List |
|
|
|
Back to top |
|
|
user9253
Joined: 28 Mar 2008 Posts: 1908 Location: Riley TWP Michigan
|
Posted: Mon Apr 08, 2019 8:03 am Post subject: Re: Battery Contactor Voltage Drop |
|
|
Paul,
The diode is fine. A voltage drop of 0.9 volts across a diode is normal. The voltage drop depends
on the diode characteristics and the current. Some power diodes will drop 1.5 volts or more.
| - The Matronics AeroElectric-List Email Forum - | | Use the List Feature Navigator to browse the many List utilities available such as the Email Subscriptions page, Archive Search & Download, 7-Day Browse, Chat, FAQ, Photoshare, and much more:
http://www.matronics.com/Navigator?AeroElectric-List |
|
_________________ Joe Gores |
|
Back to top |
|
|
ceengland7(at)gmail.com Guest
|
Posted: Mon Apr 08, 2019 9:30 am Post subject: Battery Contactor Voltage Drop |
|
|
As long as the operating voltage with the alternator running is 'normal' (around 14V), I wouldn't be concerned about a 0.9V drop from primary bus across a standard diode block. If the diode is a typical 'full wave rectifier' (square metal or plastic block with 4 leads), and the source is feeding the '-' terminal and the load is on the '+' terminal, the voltage drop will be higher since the path is actually through two diodes in series. Not a big deal as long as you understand what's happening. Only time it might matter is after alternator loss, at the very end of battery life, *if* the E bus is still fed through the diode.
Charlie
On 4/8/2019 10:31 AM, Paul Eckenroth wrote:
Quote: | Thanks for the information Charlie. The reason for the question is that I have 1 EFIS each on the regular buss and the E buss which show .9V difference. Does the diode degrade in a way that would increase voltage drop.
Paul
On Sun, Apr 7, 2019 at 5:34 PM Charlie England <ceengland7(at)gmail.com (ceengland7(at)gmail.com)> wrote:
Quote: | --> AeroElectric-List message posted by: Charlie England <ceengland7(at)gmail.com (ceengland7(at)gmail.com)>
On 4/7/2019 2:16 PM, Paul Eckenroth wrote:
> What is the typical voltage drop across the poles of a healthy battery
> contactor. Is there a failure or aging mode where the voltage drop
> increases. How about typical voltage drop across the diode bridge
> rectifier for the essential buss. After eleven trouble free years I
> need to sort out some problems with my RV9A. Thanks for any information.
>
> Paul
Drop across a good contactor should be hard to measure reliably with a
regular voltmeter.
Drop across a typical silicon diode will be zero with no load, but will
be around 0.7V at any significant load.
If you have a Schottky diode (not likely, but possible), it will be
around 0.5V or less under load.
---
This email has been checked for viruses by Avast antivirus software.
https://www.avast.com/antivirus
===========
-
Electric-List" rel="noreferrer" target="_blank">http://www.matronics.com/Navigator?AeroElectric-List
===========
FORUMS -
eferrer" target="_blank">http://forums.matronics.com
===========
WIKI -
errer" target="_blank">http://wiki.matronics.com
===========
b Site -
-Matt Dralle, List Admin.
rel="noreferrer" target="_blank">http://www.matronics.com/contribution
===========
|
|
Virus-free. www.avast.com [url=#DAB4FAD8-2DD7-40BB-A1B8-4E2AA1F9FDF2] [/url]
| - The Matronics AeroElectric-List Email Forum - | | Use the List Feature Navigator to browse the many List utilities available such as the Email Subscriptions page, Archive Search & Download, 7-Day Browse, Chat, FAQ, Photoshare, and much more:
http://www.matronics.com/Navigator?AeroElectric-List |
|
|
|
Back to top |
|
|
nuckolls.bob(at)aeroelect Guest
|
Posted: Mon Apr 08, 2019 2:48 pm Post subject: Battery Contactor Voltage Drop |
|
|
Quote: | If the diode is a typical 'full wave rectifier' (square metal or plastic block with 4 leads), and the source is feeding the '-' terminal and the load is on the '+' terminal, the voltage drop will be higher since the path is actually through two diodes in series. |
All of my drawings show power input
on an AC terminal (~) and output
on the (+). This uses only one of
the four diodes to minimize voltage
drop.
Quote: | Not a big deal as long as you understand what's happening. Only time it might matter is after alternator loss, at the very end of battery life, *if* the E bus is still fed through the diode. |
Correct. Your radios are 'speced' to function
to 10V or less. By the time a battery gets
down to 10v (lead acid) or 11.2v (LiFePO4)
the battery is 'used up'. This is why the
e-bus alternate feed switch is closed any
time the alternator is off line . . . which
lets the electro-whizzies suck the battery
dry.
Any time the alternator is working, voltage
drop in the normal feed diode is insignificant.
Bob . . .
| - The Matronics AeroElectric-List Email Forum - | | Use the List Feature Navigator to browse the many List utilities available such as the Email Subscriptions page, Archive Search & Download, 7-Day Browse, Chat, FAQ, Photoshare, and much more:
http://www.matronics.com/Navigator?AeroElectric-List |
|
|
|
Back to top |
|
|
N509RV(at)eckenroth.com Guest
|
Posted: Mon Apr 08, 2019 4:30 pm Post subject: Battery Contactor Voltage Drop |
|
|
I appreciate everyone's comments. I thought I had a problem which has now evaporated.
Paul
On Mon, Apr 8, 2019 at 6:52 PM Robert L. Nuckolls, III <nuckolls.bob(at)aeroelectric.com (nuckolls.bob(at)aeroelectric.com)> wrote:
Quote: | Quote: | If the diode is a typical 'full wave rectifier' (square metal or plastic block with 4 leads), and the source is feeding the '-' terminal and the load is on the '+' terminal, the voltage drop will be higher since the path is actually through two diodes in series. |
All of my drawings show power input
on an AC terminal (~) and output
on the (+). This uses only one of
the four diodes to minimize voltage
drop.
Quote: | Not a big deal as long as you understand what's happening. Only time it might matter is after alternator loss, at the very end of battery life, *if* the E bus is still fed through the diode. |
Correct. Your radios are 'speced' to function
to 10V or less. By the time a battery gets
down to 10v (lead acid) or 11.2v (LiFePO4)
the battery is 'used up'. This is why the
e-bus alternate feed switch is closed any
time the alternator is off line . . . which
lets the electro-whizzies suck the battery
dry.
Any time the alternator is working, voltage
drop in the normal feed diode is insignificant.
Bob . . .
|
| - The Matronics AeroElectric-List Email Forum - | | Use the List Feature Navigator to browse the many List utilities available such as the Email Subscriptions page, Archive Search & Download, 7-Day Browse, Chat, FAQ, Photoshare, and much more:
http://www.matronics.com/Navigator?AeroElectric-List |
|
|
|
Back to top |
|
|
|
|
You cannot post new topics in this forum You cannot reply to topics in this forum You cannot edit your posts in this forum You cannot delete your posts in this forum You cannot vote in polls in this forum You cannot attach files in this forum You can download files in this forum
|
Powered by phpBB © 2001, 2005 phpBB Group
|