Matronics Email Lists :: View topic

Matronics Email Lists
Web Forum Interface to the Matronics Email Lists

Get Email Distribution Too! FAQ Search Memberlist Usergroups Register

Profile Log in to check your private messages Log in

HS-1008L/R Brackets

Matronics Email Lists Forum Index -> RV10-List

View previous topic :: View next topic

Author Message

wv4i(at)bellsouth.net
Guest

Posted: Mon Sep 18, 2006 1:49 am Post subject: HS-1008L/R Brackets

Take care to note that dimensions on these angled aluminum parts go from 

1.5" on the long side end to 1.5" at angle to 1 21/32" at short side 

end. Also, note that the flare is only on one side of short angle side, 

not both. Not a big deal if caught early. Note that Air Parts has more 

AA6-187-3x3, as well as Van's, hi.....



Link McGarity

#40622



Thanks to Deems Davis' site for great pics of these parts (images 1,4,5):



http://www.deemsrv10.com/album/CNC%20Parts/index.html

- The Matronics RV10-List Email Forum -

Use the List Feature Navigator to browse the many List utilities available such as the Email Subscriptions page, Archive Search & Download, 7-Day Browse, Chat, FAQ, Photoshare, and much more:

http://www.matronics.com/Navigator?RV10-List

Rick S.

Joined: 12 Feb 2006
Posts: 347
Location: Las Vegas

Posted: Mon Sep 18, 2006 5:52 am Post subject: HS-1008L/R Brackets

Read the plans, measure twice, cut outside the finished called out dimensions and file to the finished dimensions followed by proper deburring and polishing. Consider fabricating these parts as the EDUCATIONAL part of building your aircraft. If you screw up don't make the same mistake twice  



Given that, the trim tab brackets suck and short of brazing up the provided ones I would opt for the nicely machined ones unless I had a mill handy. 



Do you think buying these parts will lower your build below the %51 percent mark?  They are somewhat time consuming but when you do finish them they sure are a small rewarding part of the construction process.



Rick S.

40185



--

- The Matronics RV10-List Email Forum -

Use the List Feature Navigator to browse the many List utilities available such as the Email Subscriptions page, Archive Search & Download, 7-Day Browse, Chat, FAQ, Photoshare, and much more:

http://www.matronics.com/Navigator?RV10-List

_________________
Rick S.
RV-10
40185

johngoodman

Joined: 18 Sep 2006
Posts: 530
Location: GA

Posted: Tue Sep 19, 2006 6:37 am Post subject: Re: HS-1008L/R Brackets

 	  wv4i(at)bellsouth.net wrote: 	
		  Take care to note that dimensions on these angled aluminum parts go from 

1.5" on the long side end to 1.5" at angle to 1 21/32" at short side 

end. Also, note that the flare is only on one side of short angle side, 

not both. Not a big deal if caught early. Note that Air Parts has more 

AA6-187-3x3, as well as Van's, hi.....



Link McGarity

#40622



Thanks to Deems Davis' site for great pics of these parts (images 1,4,5):



http://www.deemsrv10.com/album/CNC%20Parts/index.html 	




Luckily, Van's provides enough AA6... to make one more (g).

John

- The Matronics RV10-List Email Forum -

Use the List Feature Navigator to browse the many List utilities available such as the Email Subscriptions page, Archive Search & Download, 7-Day Browse, Chat, FAQ, Photoshare, and much more:

http://www.matronics.com/Navigator?RV10-List

_________________
#40572 Phase One complete in 2011

Display posts from previous:

	Matronics Email Lists Forum Index -> RV10-List	All times are GMT - 8 Hours
Page 1 of 1

Jump to:

You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot vote in polls in this forum
You cannot attach files in this forum
You can download files in this forum