Matronics Email Lists :: View topic

Matronics Email Lists
Web Forum Interface to the Matronics Email Lists

Get Email Distribution Too! FAQ Search Memberlist Usergroups Register

Profile Log in to check your private messages Log in

Riveting Question

Matronics Email Lists Forum Index -> RV10-List

View previous topic :: View next topic

Author Message

rleffler

Joined: 05 Nov 2006
Posts: 680

Posted: Tue Oct 09, 2007 4:00 pm Post subject: Riveting Question

On page 9-14, when attaching the skins to the E-903 counter balance, I’m having problems figuring out (my complete lack of creativity) how to set the last rivet towards the trailing edge.   The rivet on the top skin is set first, but there isn’t ample room to get my no hole in between to the two rivets  (top and bottom) to squeeze and clearly any bucking bar is too big.  

   

I’m sure there must be an obvious solution, I’m just not seeing it at the moment.  

   

Thanks,  

   

Bob  

   

      [quote][b]

- The Matronics RV10-List Email Forum -

Use the List Feature Navigator to browse the many List utilities available such as the Email Subscriptions page, Archive Search & Download, 7-Day Browse, Chat, FAQ, Photoshare, and much more:

http://www.matronics.com/Navigator?RV10-List

_________________
Bob Leffler
N410BL - Phase I
http://mykitlog.com/rleffler

ricksked(at)embarqmail.co
Guest

Posted: Tue Oct 09, 2007 4:12 pm Post subject: Riveting Question

Oldie but a goodie Bob, 

I used a cold chisel wedged into the trailing edge with the back rivet under the bottom skin and it came out OK, there are several ways but that was mine, others may chime in.

---

- The Matronics RV10-List Email Forum -

Use the List Feature Navigator to browse the many List utilities available such as the Email Subscriptions page, Archive Search & Download, 7-Day Browse, Chat, FAQ, Photoshare, and much more:

http://www.matronics.com/Navigator?RV10-List

jesse(at)saintaviation.co
Guest

Posted: Tue Oct 09, 2007 4:19 pm Post subject: Riveting Question

I don’t know about this specific part, but in cases like this using a pop rivet is probably acceptable.  

   

Do not archive  

     

Jesse Saint  

Saint Aviation, Inc.  

jesse(at)saintaviation.com (jesse(at)saintaviation.com)  

www.saintaviation.com  

Cell: 352-427-0285  

Fax: 815-377-3694  

        

  

From: Bob Leffler [mailto:rvmail(at)thelefflers.com] 

 Sent: Tuesday, October 09, 2007 7:59 PM

 To: rv10-list(at)matronics.com

 Subject: Riveting Question  

  

   

On page 9-14, when attaching the skins to the E-903 counter balance, I’m having problems figuring out (my complete lack of creativity) how to set the last rivet towards the trailing edge.   The rivet on the top skin is set first, but there isn’t ample room to get my no hole in between to the two rivets  (top and bottom) to squeeze and clearly any bucking bar is too big.  

   

I’m sure there must be an obvious solution, I’m just not seeing it at the moment.  

   

Thanks,  

   

Bob  

   [quote]   [b]

- The Matronics RV10-List Email Forum -

Use the List Feature Navigator to browse the many List utilities available such as the Email Subscriptions page, Archive Search & Download, 7-Day Browse, Chat, FAQ, Photoshare, and much more:

http://www.matronics.com/Navigator?RV10-List

rv10builder(at)verizon.ne
Guest

Posted: Tue Oct 09, 2007 4:24 pm Post subject: Riveting Question

pop rivet with the MK-319-BS - it will be fine  structurally.

  

 [quote]   ---

- The Matronics RV10-List Email Forum -

Use the List Feature Navigator to browse the many List utilities available such as the Email Subscriptions page, Archive Search & Download, 7-Day Browse, Chat, FAQ, Photoshare, and much more:

http://www.matronics.com/Navigator?RV10-List

rleffler

Joined: 05 Nov 2006
Posts: 680

Posted: Wed Oct 10, 2007 2:38 am Post subject: Riveting Question

Thanks for your comments.  

   

I was starting to come to the same conclusion, since there are a couple of these already on the bottom.  

       

From: owner-rv10-list-server(at)matronics.com [mailto:owner-rv10-list-server(at)matronics.com] On Behalf Of Pascal

 Sent: Tuesday, October 09, 2007 8:25 PM

 To: rv10-list(at)matronics.com

 Subject: Re: Riveting Question  

  

  

     

pop rivet with the MK-319-BS - it will be fine structurally.  

    

   

   	  Quote: 	
		      

----- Original Message -----   

    

From: Bob Leffler (rvmail(at)thelefflers.com)   

    

To: rv10-list(at)matronics.com (rv10-list(at)matronics.com)   

    

Sent: Tuesday, October 09, 2007 4:58 PM  

    

Subject: Riveting Question  

    

   

  

On page 9-14, when attaching the skins to the E-903 counter balance, I’m having problems figuring out (my complete lack of creativity) how to set the last rivet towards the trailing edge.   The rivet on the top skin is set first, but there isn’t ample room to get my no hole in between to the two rivets  (top and bottom) to squeeze and clearly any bucking bar is too big.  

   

I’m sure there must be an obvious solution, I’m just not seeing it at the moment.  

   

Thanks,  

   

Bob  

    	  Quote: 	
		    href="http://www.matronics.com/Navigator?RV10-List">http://www.matronics.com/Navigator?RV10-Listhref="http://forums.matronics.com">http://forums.matronics.com 	
   	
0 	  Quote: 	
		   	
1 	  Quote: 	
		   	
2 	  Quote: 	
		   	
3 	  Quote: 	
		   	
4 	  Quote: 	
		   	
5 	  Quote: 	
		   	
6 	  Quote: 	
		   	
7 	  Quote: 	
		   	
8 	  Quote: 	
		   	
9  



 

 __________ NOD32 2582 (20071009) Information __________

 

   

      [quote][b]

- The Matronics RV10-List Email Forum -

Use the List Feature Navigator to browse the many List utilities available such as the Email Subscriptions page, Archive Search & Download, 7-Day Browse, Chat, FAQ, Photoshare, and much more:

http://www.matronics.com/Navigator?RV10-List

_________________
Bob Leffler
N410BL - Phase I
http://mykitlog.com/rleffler

johngoodman

Joined: 18 Sep 2006
Posts: 530
Location: GA

Posted: Wed Oct 10, 2007 8:44 am Post subject: Re: Riveting Question

I see you already have an answer, but I gave up and used a blind rivet (pop).

John

- The Matronics RV10-List Email Forum -

Use the List Feature Navigator to browse the many List utilities available such as the Email Subscriptions page, Archive Search & Download, 7-Day Browse, Chat, FAQ, Photoshare, and much more:

http://www.matronics.com/Navigator?RV10-List

_________________
#40572 Phase One complete in 2011

Display posts from previous:

	Matronics Email Lists Forum Index -> RV10-List	All times are GMT - 8 Hours
Page 1 of 1

Jump to:

You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot vote in polls in this forum
You cannot attach files in this forum
You can download files in this forum